Pro Mach Orion CTS Flex Stretchwrapper Скачать руководство пользователя

Страница: 37 / 132

Orion

Machine Manual

Revision 3.0

CTS Flex Stretchwrapper

25 July 2016

System Operation

Page 3-7

Maintenance Prompt

This is the Maintenance Prompt Screen. When preventative maintenance is required the

prompt and picture of the maintenance is displayed. Press Acknowledge to confirm that

the procedure was completed and reset the counter. Press Snooze to delay the counter for

100 cycles before the prompt re-displays.

Figure 3 - 5

The Maintenance

Prompt Screen

Table 3-3. The Maintenance Prompt Screen Button Descriptions

STATE 1

DESCRIPTION

ACKNOWLEDGE

Press this button to acknowledge the required maintenance prompt as completed.

SNOOZE

Press this button to snooze the required maintenance prompt. The prompt will

remain in the alarm list and redisplay after 100 cycles and re-display until it is

acknowledged.

Содержание Orion CTS Flex Stretchwrapper





































































































































Результаты поиска

Содержание Orion CTS Flex Stretchwrapper

Отзывы:

Похожие инструкции для Orion CTS Flex Stretchwrapper

Бренды по названию

Популярные бренды

Pro Mach Orion CTS Flex Stretchwrapper, Руководство пользователя

Результаты поиска

Содержание Orion CTS Flex Stretchwrapper

Отзывы:

Похожие инструкции для Orion CTS Flex Stretchwrapper

Бренды по названию

Популярные бренды