The console features an information mode that keeps
track of the total number of hours that the elliptical
crosstrainer has been used and the total number of
miles (or kilometres) pedaled. The information mode
also allows you to select miles or kilometres as the
unit of measurement for speed and distance.
To access the information mode, press and hold the
On/Reset button for about six seconds.
When the informa-
tion mode is select-
ed, an E for English
miles or an M for
metric kilometres will
appear in the dis-
play. To change the
unit of measure-
ment, press the + button.
Press the Display
button. The display
will then show the
total number of
hours that the ellipti-
cal crosstrainer has
been used.
Press the Display but-
ton again. The display
will then show the
total number of miles
(or kilometres) ped-
aled.
To exit the information mode, press the On/Reset but-
ton again.
THE OPTIONAL CHEST PULSE SENSOR
The optional chest pulse sensor provides hands-free
operation and continuously monitors your heart rate
during your workouts. To purchase the optional
chest pulse sensor, call 08457 089 009.
6
19
7. Hold the lower end of the left Handlebar Leg (79) inside
of the left Front Spring Bracket (17). Apply a generous
amount of grease to an M10 x 78mm Button Bolt (27).
Attach the left Handlebar Leg to the left Front Spring
Bracket (17) with the Button Bolt, two M10 Washers
(38), and an M10 Nylon Locknut (29). Do not over-
tighten the Nylon Locknut; the left Handlebar Leg
must be able to pivot freely.
Attach the right Handlebar Leg (79) to the right Front
Spring Bracket (17) in the same way.
Refer to step 6. Tighten the M8 x 45mm Button Bolts
(50) in the Handlebar Legs (79). Refer to step 3.
Tighten the M10 x 88mm Button Bolt (63).
17
17
27
38
38
29
Grease
5. The Console (5) requires four 1.5V “D” batteries; alka-
line batteries are recommended. Refer to the inset
drawing. Press the tab on the battery cover, and lift off
the battery cover. Insert four batteries into the battery
compartment. Make sure that the batteries are
turned as shown by the diagram in the battery
compartment. Reattach the battery cover.
While another person holds the Console (5) in the
position shown, connect the wire harness on the
Console to the Upper Wire Harness (86). Insert the
excess wire harness into the Upright (2). Next, attach
the Console to the Upright with three M10 x 27mm
Screws (71) and three M10 Split Washers (70). Be
careful to avoid pinching the wire harnesses.
Snap the bookrack onto the Console (5) in the indicated
location.
5
Bookrack
86
71
71
6. Identify the Left Handlebar (9), which is marked with a
sticker. Insert the Left Handlebar into one of the
Handlebar Legs (79); make sure that the Handlebar
Leg is turned so the hexagonal holes are on the
indicated side. Attach the Left Handlebar to the
Handlebar Leg with two M8 x 45mm Button Bolts (50)
and two M8 Nylon Locknuts (46). Make sure that the
Nylon Locknuts are inside of the hexagonal holes.
Do not fully tighten the Button Bolts yet.
Apply a generous amount of the included grease to the
left axle on the Upright (2) and inside of the two
Handlebar Bushings (24) in the Left Handlebar (9).
Carefully slide an Upright Spacer (26), a Handlebar
Spacer (25), the Left Handlebar (9), and a Handlebar
Cap (23) onto the left axle on the Upright (2) as shown.
Slide an M10.3 Black Washer (53) onto an M8 x 19mm
Button Screw (22), and tighten the Button Screw into the
axle.
Attach the Right Handlebar and the other Handlebar Leg
(not shown) in the same way.
6
7
2
Wire
Harness
70
70
71
26
25
9
2
23
22
53
50
46
Hexagonal
Holes
79
79
79
5
Tab
Batteries
Battery
Cover
5
HOW TO USE THE INFORMATION MODE
Grease
