background image

-17-

- Do not modify the GLC unit.  Doing so may cause a fire or an

electric shock.

- Do not use the GLC in an environment where flammable gasses

are present, since operating the GLC may cause an explosion.

Wiring Warnings:

- To prevent electric shock or equipment damage, prior to install-

ing or wiring the GLC, confirm that the GLC’s power cord is un-
plugged from the power supply.

- After completing any GLC wiring work, be sure the terminal block’s

protective plastic cover is reattached. If this cover is not reat-
tached, an electric shock could easily occur.

- Do not use power levels with the GLC that are outside of the

GLC’s specified power range. Doing so may cause a fire, electric
shock or damage the GLC.

- Do not operate or store the GLC in areas where flammable gas-

ses are present, since operating the GLC may cause an explo-
sion.

Operation and Maintenance Warnings:

- Do not touch a live power terminal. This could cause a shock or

machine malfunction.

- Due to the danger of an electric shock, confirm that the GLC’s

power cord is unplugged before either cleaning the GLC or at-
taching/detaching the power terminal block screws.

- When replacing the GLC’s backlight, be sure to unplug the unit’s

power cord  to prevent a shock, and wear gloves to prevent being
burned.

- The GLC uses a lithium battery for backing up its internal clock

and control memory data. If the battery is incorrectly replaced
(i.e. the + and - sides are reversed), the battery may explode. There-
fore, before changing the battery, Pro-face recommends that you
contact your local GLC distributor for battery replacement instruc-
tions.

- Do not attempt to modify the GLC’s internal parts or wiring in any

way, since this may lead to either a shock or fire.

CAUTIONS

Wiring Layout Cautions:

- Be sure that all GLC input/output signal lines are isolated from all

power wiring or power cables, via a separate wiring duct. This is
to prevent excessive noise, which can cause a unit malfunction.

Installation Cautions:

- Be sure any data cable attached to a GLC connector is securely

attached. If the cable and connector pins do not all make com-
plete contact, incorrect input or output signals can result.e noise,
which can cause a unit malfunction.

Содержание GLC2300-LG41-24V















Отзывы: