background image

15

 

720x400 Mode When an input data resolution of 720 x 400 is used in the 

VGA text mode, set this parameter to ON. For other 

resolutions, set this parameter to OFF.
(Default: OFF)

Enables/disables the screen display Auto OFF function 

and sets the time when the Auto OFF function is 

enabled.
(Default: OFF <Auto OFF function disabled>)

The Auto OFF function automatically turns off the 

display to prevent the screen from burning out when the 

touch panel is not used for some period of time. With 

this parameter, you can set the time interval to turn off 

the screen display (how much time passes before the 

screen display is turned off) when the touch panel is not 

used. If the touch panel is not touched over the set time, 

the backlight will automatically turns off.

Select the time period from 1 min, 3 min, 5 min, 10 min, 

and OFF (Auto OFF function disabled).

Enables/disables the Backlight burnout detect function.
(Default: ON)
When a burned-out backlight is detected, the status LED 

flashes alternately green and red, or a steady orange.
Touch-operation will be disabled when the backlight 

burns out, which prevents the FP from sending input 

signals to the PLC.

BL Alarm

• Normally, the FP unit detects a backlight burnout by 

monitoring the backlight’s current flow, however, the FP 

may fail to detect this condition, depending on the type of 

backlight problem.

Auto off Disp

Selection of the change item

System Settings

Enables/disables the click sound. With this parameter, 

the sound level can also be adjusted.
(Default value: OFF <Click sound disabled>)

Click Tone

Adjustment button

Applies the setting and then returns to the top menu.

Cancels the setting and then returns to the top menu.

Содержание FP3650-T41

















Отзывы: