PRISMJET 54 Gen2, Руководство по эксплуатации

Страница: 62 / 305

Before using PrismJET 54 Gen2 OPERATION MANUAL
72 3.5 Test print
3.5.4 Setup print
Used to check the current setup of the printer.
NOTE
• Keep the printed setup print at hand.
TIP
Refer to the following for printing procedure.
3.5 Test print
㹑㹣㹲㹳㹮ࠉ㹊㹧㹱㹲
㸺㹇㹬㹤㹭㹰㹫㹟㹲㹧㹭㹬㸼 㸺㹂㹧㹱㹮㹪㹟㹷㸼
SerialNo.
Model
Memory Size
Total print
Firmware M
Firmware C
= XXX m 2
= V 1.00
= V 1.10
㸺㹋㹣㹬㹳 㹑㹣㹲㹳㹮㸼
[Number][Select]Menu 㸻 Setup
[ 1][*]User Type
㸻
Type 1
[1]Print Mode 㸻 High Quality (Effect 㸻 i-Screen)
[2]Adjust Print
[3]PF Adjust
[1]Auto
[2]Initial Adj.Print
[3]Initial Adjust
㸻
250.0/250mm
[4]Confirm Adj.Print
[5]Micro Adj. Print
[6]Micro Adjust 㸻 0.00%
[4]PreHeater
㸻
30
㺽
C
[5]PlatenHeater 㸻 30 㺽 C
[6]Dryer
㸻
30
㺽
C
[7]Vacuum Fan 㸻 Mediuum
[8]Thickness
㸻
170 mm
[9]UserCopy
[ 2][*]Spitting
㸻
On(Pass Count = 1cnt)
[ 3][*]Side Margin 㸻 5mm
[ 4][*]Media Initial
㸻
Width
[ 5][*]Media Width 㸻 1000mm
[ 6][*]Output Mode
㸻
Off
[ 7][ ]Method of Cut 㸻 SingleCut-2steps(InkDryerTimer= 0sec)
[ 8][*]Origin
[ 9][ ]Prevent Stick 㸻 Off
[10][*]Standby Heating
㸻
60min
[11][*]Head Travel 㸻 Data
[12][*]Multi Strike
㸻
1cnt
[13][*]Strike Wait 㸻 0.0sec
[14][*]Media Slant
㸻
On
[15][*]Auto Cleaning
WaitingTime
㸻
360min
PrintingTime 㸻 Off
Before Print
㸻
Off
[16][*]Longstore
[17][*]CR Maintenance
[18][*]Initialization
= XXXX000001
= XPJ-1341SR-P
= 256MB
Language = English
Temperature 㸻 Celsius[ 㺽 C]
Length
㸻ࠉ
mm
2021/07/01 0:00
Head Height : Low Cleaning Mode: Normal
[Number][Select]Menu 㸻 Setup
[19][*]IP Address
㸻
192.168.001.253
[20][*]Subnet Mask 㸻 255.255.255.0
[21][*]Gateway
㸻
192.168.001.254
[22][*]Header Dump 㸻 Off
[23][*]Start Feed
㸻
0.0mm
[24][*]Alert Buzzer 㸻 On
[25][*]FrontInterlace
㸻
Auto
[26][*]Select Nozzle
[1]Print
[2]Nozzle Settings 㸻 Nozzle ALL
<Ink Status>
SmartChip KCMY 85/ 85/ 28/ 24
<Life Times>
Head : E ★★★★★F
Pump : E ★★ F
CR Motor : E ★★★★★F
PF Motor : E ★★ F
<SleepModeSettings>
CleaningTimer 㸻 24h
<RollPaperRemain>
[1]Print
[2]Simple Print
[3]Scan
[4]Roll Length 㸻 Roll1 (Length 㸻P )
(PrintStop
㸻2Q1HDU(QG 㸻P
)
[5]Auto Scan
㸻
On
＜User Type List＞
Type 1 Type 2 Type 3 Type 4 Type 5
Type 6 Type 7 Type 8 Type 9 Type10
Type11 Type12 Type13 Type14 Type15
Quality Quality Quality Quality Quality
i-Screen i-Screen i-Screen i-Screen i-Screen
Off Off Off Off Off
Off Off Off Off Off
0.00% 0.00% 0.00% 0.00% 0.00%
250.0 / 250mm 250.0 / 250mm 250.0 / 250mm 250.0 / 250mm 250.0 / 250mm
User Type
Print Mode
Print Mode＞Effect
PF＞Initial Adjust
PF＞Micro Adjust
PreHeater
PlatenHeater
Off Off Off Off Off Dryer
High High High High High
170μm 170μm 170μm 170μm 170μm
Vacuum Fan
Thickness
Off Off Off Off Off
Off Off Off Off Off
PreHeater
PlatenHeater
Off Off Off Off Off Dryer
High High High High High
170μm 170μm 170μm 170μm 170μm
Vacuum Fan
Thickness
Off Off Off Off Off
Off Off Off Off Off
PreHeater
PlatenHeater
Off Off Off Off Off Dryer
High High High High High
170μm 170μm 170μm 170μm 170μm
Vacuum Fan
Thickness
User Type
Print Mode
Print Mode＞Effect
PF＞Initial Adjust
PF＞Micro Adjust
User Type
Print Mode
Print Mode＞Effect
PF＞Initial Adjust
PF＞Micro Adjust
Quality Quality Quality Quality Quality
i-Screen i-Screen i-Screen i-Screen i-Screen
0.00% 0.00% 0.00% 0.00% 0.00%
250.0 / 250mm 250.0 / 250mm 250.0 / 250mm 250.0 / 250mm 250.0 / 250mm
Quality Quality Quality Quality Quality
i-Screen i-Screen i-Screen i-Screen i-Screen
0.00% 0.00% 0.00% 0.00% 0.00%
250.0 / 250mm 250.0 / 250mm 250.0 / 250mm 250.0 / 250mm 250.0 / 250mm