manualshive.com logo in svg

Primus D55, Руководство по обслуживанию

Поделиться
Скачать
Primus D55 Скачать руководство пользователя страница 59

70276001

57

Section 6 Adjustments

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the tumbler before servicing.
• Close gas shut-off valve to gas tumbler before servicing.
• Close steam valve to steam tumbler before servicing.
• Never start the tumbler with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be 

reconnected to ensure that the tumbler is properly grounded.

W002

WARNING

IMPORTANT: Adjusting the cylinder belt tension 
WILL AFFECT the drive belt tension. You MUST 
check and readjust the drive belt tension after 
adjusting the cylinder belt tension.

CYLINDER CLEARANCE
The clearance between the cylinder rim and front 
panel must be adjusted so the cylinder is centered 
within the front panel opening when the cylinder 
is fully loaded and is turning. However, the 
adjustment should be made when the cylinder is 
empty.

NOTE: If the cylinder is not properly adjusted, the 
cylinder rim will rub against the front panel.

a. Open loading door.
b. Check the gap between the center of the front 

panel top flange and the cylinder rim. Proper 
adjustment is when the gap is 8/32 inch ± 3/32 
inch. Refer to Figure 27. Perform steps d 
through i to adjust the cylinder rim/front panel 
flange clearance.

c. Check the cylinder fore/aft clearance between 

the inside front of the cylinder and the edge of 
the front panel flange. Proper adjustment is 
when the gap is 9/32 inch ± 1/32 inch. Refer to 
Figure 27. Perform steps j through n to adjust 
the cylinder fore/aft clearance.

CYLINDER RIM/FRONT PANEL FLANGE 
CLEARANCE ADJUSTMENT
a. Support corner drive guard and remove screws 

holding corner guard to rear of tumbler.

b. Support drive guard cover and remove screws 

holding guard to rear of tumbler.

c. Loosen rear bearing mounting screws. Refer to 

Figure 28

d. Loosen the locknuts on rear adjustment screws. 

Refer to Figure 28.

e. Turn the adjusting screws in or out as necessary 

to obtain proper clearance between cylinder rim 
and front panel.

NOTE: Turning the adjusting screws clockwise will 
raise the cylinder and turning them counter-
clockwise will lower the cylinder. Turn both screws 
evenly to adjust top and bottom clearance. Turn one 
or the other adjusting screw in or out to adjust side 
clearance.

f. After the cylinder is properly adjusted, tighten 

the adjusting screw locknuts and the rear 
bearing mounting screws.

g. Install drive guard cover. Refer to 

Paragraph 49.

NOTE: If adjusting the trunnion housing fails to 
correct the clearance, the problem is probably due 
to a worn trunnion shaft or defective bearings.

Figure 26

T317PE1B_

Jackshaft

Assembly

Jackshaft

Assembly

Attaching

Screws

Содержание D55



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды