manualshive.com logo in svg

Primus D55, Руководство по обслуживанию

Поделиться
Скачать
Primus D55 Скачать руководство пользователя страница 18

16

70276001

Section 3 Troubleshooting

To reduce the risk of electric shock, fire, explosion, serious injury or death:
• Disconnect electric power to the tumbler before servicing.
• Close gas shut-off valve to gas tumbler before servicing.
• Close steam valve to steam tumbler before servicing.
• Never start the tumbler with any guards/panels removed.
• Whenever ground wires are removed during servicing, these ground wires must be 

reconnected to ensure that the tumbler is properly grounded.

W002

WARNING

15. WATER IN STEAM LINE - STEAM MODELS

POSSIBLE CAUSE

TO CORRECT

Incorrect installation of steam piping. 

• Refer to Installation Manual for steam requirements.

Trap functioning improperly.

• Check trap for size and capacity. If trap is dirty or 

sluggish, clean thoroughly or replace. Check return line 
for high back pressure. Check trap for proper installation. 
Refer to Installation Manual for requirements.

Содержание D55



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды