PRG BEST BOY HP SPOT LUMINAIRE Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 241

PRG BEST BOY HP SPOT LUMINAIRE Скачать руководство пользователя страница 19

BEST BOY

®

HP SPOT LUMINAIRE

|

SERVICE MANUAL

|

DESCRIPTION

PAGE

9

Gobo Wheel Standard Configurations

The following drawings show the standard Gobo Wheel configurations.

Figure 1-8: Gobo Wheel Standard Configurations

About Moiré Gobos

Moiré gobos contain two pieces of glass: one that is fixed and another that rotates. Since the two pieces of glass are
very close together, it creates an interesting interference effect (which is referred to as the "moiré"). Due to this
construction they do not contain sensors, and therefore cannot be calibrated to a certain orientation at startup as with
standard gobos.

CAUTION

When you add or remove a Moiré gobo, it is critical to change the menu settings.
Failure to do this will cause the wheel not to calibrate, and likely damage the fixture.

GOBO WHEEL 1

GOBO WHEEL 2

POSITION #1

JUST ROCKS

(17.1131.1007.01)

OPEN

POSITION #2

PIN HOLE BREAKUP

(17.1131.1002.00)

POSITION #3
SLITS
(17.1131.1001.00)

POSITION #4
SLATE WALL 4
(17.1131.1006.01)

POSITION #5
KALEIDOSCOPE MOIRÉ
(17.7101.0400.00)

POSITION #6
CLUBBED SPIRAL
(17.1131.1030.00)

OPEN

POSITION #1

CHICLETS

(17.1131.5000.00)

POSITION #2

OAK FOLIAGE 1

(17.1131.1010.00)

POSITION #3

CRACKLE LINEAR

(17.1131.1013.00)

POSITION #4
GHOST DUST
(17.1131.1022.04)

POSITION #5
FIREWATER ANIMATION
(17.7101.0401.00)

POSITION #6
STRAW 2
(17.1131.1022.03)

«
...
17
18
19
20
21
...
»

Содержание BEST BOY HP SPOT LUMINAIRE


















































































































































































































































Отзывы:

Нет отзывов