background image

APS901TM_RevB_12/20

11

 Feature 5: 

Engine Confirmation

Func�on: 

Determine how the system knows if remote start was successful.

Setting Choices:

•  Option 1 - 

Determined by 

measurement

 from the 

Purple/White

 Tach Input wire.

•  Option 2 - 

Determined by the 

voltage difference

 before remote start and a�er as set in 

Bank 3, Feature 6

.

•  Option 3 - 

Receives informa�on through an a�ached 

data bus interface

•  Option 4 - No sensing

; assumes vehicle has started based on setting in 

Bank 3, Features 11 & 14

.

 Remote Start Control (Bank 3) (cont.) 

See page 15 for Programming Instruc�on.

 Detailed Descriptions: 

Setup Op�ons

 Feature 11: 

Maximum

 

Crank Time

Func�on: 

Set maximum crank time for all remote start settings.

Setting Choices:

•  Option 1 - 

Starter will crank for 

.8

 

second

s.

•  Option 2 - 

Starter will crank for 

1

 

second

.

•  Option 3 - 

Starter will crank for 

1.5

 

seconds

.

•  Option 4 - 

Starter will crank for 

2

 

seconds

•  Option 5 - 

Starter will crank for 

4

 

seconds

.

 Feature 6: 

Start Sensing Voltage Level

Func�on: 

Set the sensitivity of voltage variance measurement to determine if the vehicle has started when Feature 5 is 

set to option 2, Voltage.

Setting Choices:

•  Option 1 - High:

 Voltage difference before remote start and a�er must be greater than .5 volts.

•  Option 2 - Low:

 Voltage difference before remote start and a�er must be less than .5 volts.

 Feature 9: 

Accessory Output Function (Purple)

Func�on: 

Set the functionality of the programmable Accessory output. 

Setting Choices:

•  Option 1 - 

Wire sends 12-Volt (+) during igni�on; 

drops out

 

during start.

•  Option 2 - 

Wire sends 12-Volt (+) during igni�on 

and start.

•  Option 3 - 

Wire sends 12-Volt (+) during start 

only.

 Feature 7: 

Ignition 2 Output Function (Green)

Func�on: 

Set the functionality of the programmable Ignition 2 output. 

Setting Choices:

•  Option 1 - 

Wire sends 12-Volt (+) during igni�on

 and start.

•  Option 2 - 

Wire sends 12-Volt (+) during igni�on; 

drops out during start

.

•  Option 3 - 

Wire sends 12-Volt (+) during start 

only

.

 Feature 8: 

Ignition 3 Output Function (Pink)

This Feature is not available on this model.

 Feature 10: 

Transmission Type

This Feature is not available on this model.

Содержание APS901TM























Отзывы: