background image

Page 3

For generator technical questions, please call 1-800-444-3353. 

For engine technical questions, please call 1-800-520-0882.

ITEM 61169 

        

SAFETY

Op

ERA

TION

M

AINTENANCE

SETU

p

WARNING SYMBOLS AND DEFINITIONS

This is the safety alert symbol.  It is used to alert you to potential 

personal injury hazards.  Obey all safety messages that 

follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided,  

will result in death or serious injury.

Indicates a hazardous situation which, if not avoided,  

could result in death or serious injury.

Indicates a hazardous situation which, if not avoided,  

could result in minor or moderate injury.

Addresses practices not related to personal injury.

Symbol Definitions

Symbol

property or Statement

RpM

Revolutions Per Minute

Hp

Horsepower

AWG

American Wire Gauge

WARNING marking concerning 

Risk of Eye Injury.  Wear ANSI-approved 

safety goggles with side shields.

Read the manual before 

set-up and/or use.

Symbol

property or Statement

WARNING marking concerning 

Risk of Hearing Loss.  

Wear hearing protection.
WARNING marking concerning 

Risk of Respiratory Injury.  

Operate engine OUTSIDE and far away 

from windows, doors, and vents.
WARNING marking concerning 

Risk of Fire while handling fuel.  

Do not smoke while handling fuel.
WARNING marking concerning 

Risk of Fire.   

Do not refuel while operating. 

Keep flammable objects 

away from engine.

IMpORTANT SAFETY INSTRUCTIONS

WARNING! Read all instructions.

 

Failure to follow all instructions listed below may result in fire, serious injury and/or DEATH. 

The warnings and precautions discussed in this manual cannot cover all possible conditions and 

situations that may occur.  It must be understood by the operator that common sense and caution 

are factors which cannot be built into this product, but must be supplied by the operator.

SAVE THESE INSTRUCTIONS

Содержание 61169





























Отзывы: