background image

 

11 

 

Route cables under the rear pedestal (optional) 

When the AMT faces away from the cable raceway, use the conduit included in the 

hardware kit to route the Ethernet, TV, and power cables underneath the center of 

the AMT and through its rear pedestal. 

To use the conduit: 

1.

 

Lay out the cables so that they pass directly under the center support of the 
AMT and place the conduit 

  on the floor directly behind the center support. 

2.

 

Insert the cables, one at a time, into the slot at the top of the conduit. 

Important  

DO NOT clip or tie the segments of the cables that you insert into the 

conduit. 

3.

 

Lower the rear pedestal over the back frame tube and the side arm supports. The 

pedestal should sit flat on the floor and with the conduit completely inside of it 

(see Figure 14). 

 

Figure 14 

 

 

To replace the access covers: 

4.

 

Guide the front cover around the arms so that the tabs at the bottom corners are 

inside the two side covers. Slide it into place until the latches on the side covers 

click into place (see Figure 15). 

 

Figure 15 

5.

 

Reattach the bottom corners of the front cover using two #10 x 3/4-inch screws. 

Fully tighten. 

Important  

In the following step, DO NOT apply excessive force to seat the cover. 

6.

 

Position the rear edge of the top cover so that the clips on the top and back 

covers are engaged securely. 

7.

 

Using the heel of your hand, gently snap the front edge of the top cover into 

place. 

8.

 

Wrap the gasket around the center support below the heart rate sensor grips, 

then fit it into the top cover making sure the edges of the seal are flush with the 

top cover (see Figure 16). 

 

Figure 16 

 

Содержание AMT 885














































Отзывы: