Precision Digital Corporation SuperNova PD500 Скачать руководство пользователя страница 39

Страница: 39 / 62

SuperNova PD500 PID Process & Temperature Controllers

Instruction Manual

Alarm Group (G.ALM)

The Alarm Group contains parameters to establish

alarm conditions for up to four alarms. These alarms

may be assigned to the SUB1 or SUB2 alarm output

relays.
This group also contains the programming of the loop

break alarm (LBA). This is a special type of alarm that

can be assigned to a Sub relay.
During programming of the Alarm Group, references

to “n” in the programming menus refers to the number

1, 2, 3, or 4; the alarm number the parameter applies

to. For example, An.TY could appear as A1.TY,

A2.TY, A3.TY, or A4.TY, each referring to alarm 1, 2,

3, and 4.
Only alarm numbers or LBA settings assigned to the

SUB1 or SUB2 relay in the Sub Relay Group (G.SUB)

will appear in the Alarm Group (G.ALM). Alarm

numbers or LBA settings that are not assigned to a

Sub relay will retain their programming and appear in

the G.ALM menu if again assigned to a Sub relay.

Alarm Number n Type (An.TY)

With An.TY, you can choose between 'Alarm off' and

13 alarm types listed in the

Alarm Type and Number

Table.

Each type is divided into absolute alarm and deviation

alarm, with or without standby mode.

An.TY

No.

Alarm Name

Absolute

Value or

Deviation

Alarm

Standby

Alarm Off

Deviation

High Absolute

Absolute

Low Absolute

Absolute

High Deviation

Deviation

Low Deviation

Deviation

High-Low

Deviation

High-Low Range

Deviation

High absolute with

standby sequence

Absolute

Yes

Low absolute with

standby sequence

Absolute

Yes

High deviation with

standby sequence

Deviation

Yes

Low deviation with

standby sequence

Deviation

Yes

High-Low deviation

with standby

sequence

Deviation

Yes

High-Low range

with standby

sequence

Deviation

Yes

Sensor error

Absolute

Figure 26. Alarm Type and Number Table

Alarm Number n Value (AL-n)

The AL-n parameter sets the alarm value for alarms

1, 2, 3, or 4; as indicated in the “n” position of the

parameter name.

When the alarm is set as an absolute value alarm, the

setting can be any value within the limits of the input

type. AL-n is entered as the displayed value, in

displayed engineering units, at which the alarm is to

turn on.
When the alarm is set as a deviation alarm, the

setting can be 0 to 100% of the full range of the input,

and is entered in the displayed engineering units, but

the number represents the absolute value of the

deviation amount at which the alarm turns on.
For example, when a type K thermocouple is used,

and the alarm type is set as a high absolute (An.TY

set to 1), the setting range of AL-n cab be -200°C to

1,370°C
When the alarm type is set as a high deviation (An.TY

is set to 3), the setting range of AL-n can be 0.0°C

1,570.0°C.

Alarm Number n Deadband (An.DB)

The alarm deadband is the different between the set

and reset points of an alarm. An.DB is entered as the

deadband for the alarm, entered in displayed

engineering units. The alarm deadband can be set as

0 to 100% of the full range of the input, regardless of

the alarm being an absolute or deviation alarm

Содержание SuperNova PD500































































Результаты поиска

Содержание SuperNova PD500

Отзывы:

Precision Digital Corporation SuperNova PD500, Инструкция по эксплуатации, Страница: 39 / 62

Результаты поиска

Содержание SuperNova PD500

Отзывы: