background image

 
 
 
 

STAND-ALONE MODE

 

Press the UP or DOWN button to select 

 (self test), and then press ENTER button to confirm 

it. The projector will run in stand-alone mode automatically under programmes have been set. 
 
 
 
 

MAINTENANCE 

If the projector’s lens becomes damaged or broken it should be replaced. If the lamp becomes 
damaged or deformed in any way it must be replaced. If the light from the lamp appears dim this would 
normally indicate that it is reaching the end of its life and it should be changed at once, old lamps run 
to the extremity of their life can explode. If the projector does not function, check the power fuse inside 
the projector, it should only be replaced by fuse with the same specified value 6.3A/250V (fast blow, 
5mmx20mm). On the main PCB inside the projector there is also 2 fuses rated 6.3A/250V and 
4A/250V (fast blow, 5mmx20mm) respectively. 

When change the fuses, please undo the 4 M6 

screws on the base of the projector and then open the base cover

. Should these be damaged call 

a qualified technician before replacement. The projector has thermal protection device that will switch 
off the projector in case of overheating. 
 

Any maintenance work should only be carried out by qualified technicians. 

 
 
 
 

KEEPING THE PROJECTOR CLEAN 

To ensure the reliability of the projector it should be kept clean. The lens and dichroic colour filters 
should also be regularly cleaned to maintain an optimum light output.

 

Do NOT use any type of 

solvent on dichroic colour filters. 

 
Cleaning frequency depends on the environment in which the fixture operates: damp, smoke or 
particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics. A soft cloth 
and typical glass cleaning products should be used in cleaning. It is recommended to clean the 
external optics at least once every 20 days and clean the internal optics at least once every 30 / 60 
days. 

 

Do not use any organic solvent, e.g. alcohol, to clean the reflector, colour 
filters or housing of the apparatus. 

 
 
 
 

TROUBLESHOOTING 

PROBLEM POSSIBLE 

CAUSE 

ACTION 

The projector doesn’t switch 
on 

-The power supply is not 
present 
-The lamp is not working 

Check the fuse on the power socket.
 
Replace the lamp. 

The lamp comes on but the 
projector doesn’t respond to 
the controller 

-Wrong DMX configuration 
and/or start address 
- Defective DMX cable 

Make sure that the projector is 
correctly configurated. 
Replace or repair the DMX cable. 

The beam appears dim 

-Dust or grease contamination 
on the optics. 
-The lamp is at the end of its 
life 

Check the optics are clean. 
 
Replace with a new lamp of the 
specified type and rating. 

 
 

Design 150 manual.doc 

8/12

Содержание DESIGN 150













Отзывы: