PPI Zenex Скачать руководство пользователя страница 3

Страница: 3 / 46

FRONT PANEL LAYOUT

Figure 1.1

PPI

OP1

OP2

OP3

Upper Readout

Lower Readout

Output-3 Indicator

ENTER Key

UP Key

DOWN Key

PAGE Key

Output-1 Indicator

Output-2 Indicator

Soak Status
Indicator

Balance Soak
Time Indicator

zenex

The front panel contains digital readouts, LED indicators and keys.

READOUTS

The Upper Readout is a 4 digit, 7-segment bright red LED display and usually displays the PV (Process Value). In Program

Mode, the Upper Readout displays parameter values/options.

The Lower Readout is a 4 digit, 7-segment bright green LED display and usually displays SP (Control Setpoint) Value. In

Program Mode, the Lower Readout displays parameter names (prompts).

INDICATORS

The Table 1.1 lists each front panel LED and the associated status.

Table 1.1

Status

Indicator

Glows while the Lower Readout shows the Balance Soak Time in Main display

mode.

• Flashes while the Soak Timer is counting down.

• Glows steadily while the Soak Timer is outside the Timer Start Band or Hold

Band (that is, HOLD state).

• Indicates Output-1 ON/OFF status if the Control Output is Relay or SSR

drive.

• Remains OFF if the Control Output is DC Linear.

OP1

• Indicates Output-2 status if OP2 function is Auxiliary / Blower Control.
• Flashes Alarm-1 status if OP2 function is Alarm.

OP2

OP3

• Indicates Output-3 status if OP3 function is Auxiliary Control.
• Flashes Alarm-2 status if OP3 function is Alarm.

User Manual

zenex

Section 1

Содержание Zenex















































Результаты поиска

Содержание Zenex

Отзывы:

Похожие инструкции для Zenex

Бренды по названию

Популярные бренды

PPI Zenex, Руководство пользователя

Результаты поиска

Содержание Zenex

Отзывы:

Похожие инструкции для Zenex

Бренды по названию

Популярные бренды