PPI Zenex Скачать руководство пользователя страница 13

Страница: 13 / 46

None

Alarm

Control

Blower

(Default : None)

Parameter Description

Settings

Default Value

Table 5.1

OUTPUT-2 FUNCTION SELECTION

None

OP2 module not installed or function not used.

Alarm

OP2 relay activates as Alarm status.

Auxiliary Control

OP2 relay activates as Auxiliary control status.

Blower

OP2 relay activates as Blower / Compressor control status.

OP2 Function : Alarm-1

Parameter Description

Settings

Default Value

TYPE

Process Low

The alarm activates for PV less than or equal to Alarm Setpoint.

Process High

The alarm activates for PV greater than or equal to Alarm Setpoint.

Deviation Band

The alarm activates if the PV deviation from SP is greater than the
set positive or negative ‘Deviation Band’ value.

Window Band

The alarm activates if the PV deviation from SP is greater than the
set ‘Window Band’ value in either direction.

End Of Soak

The OP2 Relay / SSR is switched ON for the time duration set for
the parameter ‘Alarm Timer’.

SETPOINT

Available for ‘Process High’ or ‘Process Low’ Alarms. Sets the
Upper (Process High) or Lower (Process Low) Alarm Limit.

Min. to Max. Range for
the selected Input type

(Default : 0)

DEVIATION BAND

Available for ‘Deviation Band’ Alarm. Sets a deviation band above
(Positive value) or below (Negative value) the SP for alarm
activation.

-1999 to 9999

-199.9 to 999.9

(Default : 0)

WINDOW BAND

Available for ‘Window Band’ Alarm. Sets a symmetrical band
above and below the SP for alarm activation.

3 to 999

0.3 to 99.9

(Default : 3)

User Manual

zenex

OP2 FUNCTION PARAMETERS

Section 5

Process Low

Process High

Deviation Band

Window Band

End of Soak

(Default : Process Low)

Содержание Zenex















































Результаты поиска

Содержание Zenex

Отзывы:

Похожие инструкции для Zenex

Бренды по названию

Популярные бренды

PPI Zenex, Руководство пользователя

Результаты поиска

Содержание Zenex

Отзывы:

Похожие инструкции для Zenex

Бренды по названию

Популярные бренды