manualshive.com logo in svg

PPI HumiTherm Ultra, Руководство пользователя, Страница: 54 / 63

Поделиться
Скачать
PPI HumiTherm Ultra Скачать руководство пользователя страница 54

52

HumiTherm Ultra

 

User Manual

 

The figure above illustrates 3 cases. Case (1) illustrates power-up delay. In case (2); the time elapses before PV rises above 

the SP. The compressor is thus switched ON as soon as the PV rises above the SP. In case (3); the PV rises above the SP while 

the time delay is still in progress. The compressor is switched ON as soon as the delay time elapses.

The following table list various parameters related to Compressor Switching Mode / Operation & their respective locations. 

Compressor
Status

OFF

ON

20.0

19.8

21.0

°C

Case 2

Case 3

Case 1

PV (Temperature)
SP

Compressor Switch-ON Level
Compressor Switch-OFF Level

Compressor Switch-ON Level = 20.0 + 1.0 = 21.0°C 

Temperature SP = 20.0°C 
Compressor Set-point = 1.0°C 
Compressor Hysteresis = 1.2°C 

Compressor Switch-OFF Level = 21.0 - 1.2 = 19.8°C 

Parameter Name

Navigation

(Where to Locate)

Factory

Compressor

Mode 

Boundary SP

Time Delay

Hysteresis

Zone Select

Содержание HumiTherm Ultra
































































Отзывы:

Нет отзывов