PowerVent 43VP40E2 страница 12 Скачать руководство пользователя

Страница: 12 / 40

Installing the water heater.

The water heater must be installed with the factory supplied blower assembly in place.

Venting

The.water.heater.must.be.vented.to.the.

outdoors.as.described.in.these.instructions ..

DO.NOT.connect.this.water.heater.to.

an.existing.vent.or.chimney.-.it.must.

be.vented.separately.from.all.other.

appliances .
NOTICE:.This.unit.can.be.vented.using.

only.the.following.recommended.pipe.

material ..Use.only.2-.or.3-inch.diameter.

pipe ..
PVC.(Schedule.40,.ASTM.D1785)
CPVC.(Schedule.40,.ASTM.F441)
ABS.(Schedule.40,.ASTM.D2661)
ABS..(Schedule.40.DWV,.Cellular.Core,.

ASTM.F628)

The.fittings,.other.than.the.TERMINATION,.

should.be.equivalent.to.the.following:
PVC.(Schedule.40.DWV,.ASTM.D2665)
CPVC.(Schedule.40,.ASTM.F438)
ABS.(Schedule.40.DWV,.ASTM.D2661)
The.unit.may.be.vented.horizontally.

through.a.wall.or.vertically.through.the.

roof .
Vent.pipe.runs.must.be.adequately.

supported.along.both.vertical.and.

horizontal.lengths ..
Maximum.unsupported.length.is.

recommended.to.be.no.more.than.6.feet .
It.is.imperative.that.the.first.hanger.

be.located.on.the.horizontal.length.

immediately.adjacent.to.the.first..

90-degree.elbow.from.the.vertical.rise.of.

vent.pipe.connected.to.the.water.heater .
The.support.method.used.should.isolate.

the.vent.pipe.from.floor.joists.or.other.

structural.members.to.help.prevent.the.

transmission.of.noise.and.vibration .
Do.not.support,.pin.or.otherwise.secure.

the.venting.system.in.a.way.that.restricts.

the.normal.thermal.expansion.and.

contraction.of.the.chosen.venting.material .
If.the.water.heater.is.being.installed.as.a.

replacement.for.an.existing.power.vented.

water.heater,.a.thorough.inspection.of.

the.existing.venting.system.must.be.

performed.prior.to.any.installation.work ..

..Verify.that.the.correct.materials.as.

detailed.above.have.been.used,.and.

that.the.minimum.or.maximum.vent.

length.and.terminal.locations.as.

detailed.in.this.manual.have.been.

met .

..Carefully.inspect.the.entire.venting.

system.for.any.signs.of.cracks.or.

fractures,.particularly.at.the.joints.

between.elbows.or.other.fittings.and.

the.straight.length.of.vent.pipe .

..Check.the.system.for.signs.of.sagging.

or.other.stresses.in.the.joints.as.a.

result.of.misalignment.of.any.

components.in.the.system .

..If.any.of.these.conditions.are.found,.

they.must.be.corrected.in.accordance.

with.the.venting.instructions.in.this.

manual.before.completing.the.

installation.and.putting.the.water.

heater.into.service .

NOTICE: The vent piping must be

connected to the blower assembly

using the rubber coupling and supplied

clamps. The vent pipe connections at

the blower assembly must be leak tested

with soap and water solution upon

initial startup. Repair any leaks before

allowing the water heater to operate.

DANGER: Failure to

install the blower assembly

and properly vent the water

heater to the outdoors as

outlined in the Venting

section of this manual will

result in unsafe operation of

the water heater causing

bodily injury, explosion,

fire or death.
To avoid the risk of fire,

explosion, or asphyxiation

from carbon monoxide,

NEVER operate the water

heater unless it is properly

vented and has adequate air

supply for proper operation

as outlined in the Venting

section of this manual.
The vent pipe must overlap

a minimum of ½” on each

connection. It is important

that the vent pipe engages

fully into any pipe fitting

and be kept in that position

until the adhesive has fully

cured. DO NOT drill or

punch holes in the plastic

pipe or fittings.
NOTICE: This unit is

equipped with a Flammable

Vapor Sensor. Do not

apply power until enough

time has passed to allow the

vapors from the primer and

cement to dissipate.

Blower Assembly Installation

Connect.blower.assembly.with.the.electrical.connector ..Attach.

Blower.Assembly.to.top.pan.using.the.six.(6).screws.provided.

(See.diagram.to.the.left) ..Install.rubber.coupling.(supplied.in.

the.box.with.water.heater).on.blower.housing.and.secure.it ...

Do not overtighten screws to ensure plastic does not crack.
NOTICE:

..The.Blower.Assembly.is.model.specific.and.only.

the.blower.assembly.supplied.should.be.used.on.this.water.

heater .

Additional installation information for The

Commonwealth of Massachusetts is located

on the back page of this manual.

Flue

Baffle

Rubber

Coupling

Blower

Assembly

Содержание 43VP40E2









































Результаты поиска

Содержание 43VP40E2

Отзывы:

Похожие инструкции для 43VP40E2

Бренды по названию

Популярные бренды

PowerVent 43VP40E2, Инструкция по использованию и уходу

Результаты поиска

Содержание 43VP40E2

Отзывы:

Похожие инструкции для 43VP40E2

Бренды по названию

Популярные бренды