PowerVent 43VP40E2 страница 11 Скачать руководство пользователя

Страница: 11 / 40

WARNING: Do not attempt to convert this water heater for use with a different type of gas other than the type

shown on the rating plate. Such conversion could result in hazardous operating conditions.

Leak Testing

The.water.heater.and.its.gas.connections.

must.be.leak.tested.at.normal.operating.

pressures.before.it.is.placed.in.operation .

...Turn.on.the.manual.gas.shut-off.

valve.near.the.water.heater .

...Use.a.soapy.water.solution.to.test.for.

leaks.at.all.connections.and.fittings ..

Bubbles.indicate.a.gas.leak.that.must.

be.corrected ..

The.factory.connections.to.the.gas.

control.(thermostat).should.also.be.leak.

tested.after.the.water.heater.is.placed.in.

operation .

High Altitude

Input.rating.of.this.water.heater.is.

based.on.sea.level.operation ...At.higher.

elevations.the.actual.input.rate.may.be.

lower.than.the.value.listed.on.the.rating.

label.due.to.the.derating.of.natural.gas.and.

LP.gas ...This.water.heater.can.be.installed.

at.elevation.up.to.2,000.feet.without.any.

change.or.modification .

For.installation.between.2,000.and.7,700.

feet,.refer.to.the.Venting.Information.

tables.on.page.13.and.14.for.maximum.

vent.lengths .
Installations.above.7,700.feet.are.not.

authorized .
Contact.the.local.gas.supplier.for.more.

information .

Pressure Testing the Gas Supply System

The.water.heater.and.its.manual.gas.

shut-off.valve.must.be.disconnected.from.

the.gas.supply.piping.system.during.any.

pressure.testing.of.that.system.at.

pressures.in.excess.of.3/8.psi.(10 .5”.w .c .).

for.natural.gas,.or.1/2.psi.(14”.w .c .).for.

LP.gas .

The.water.heater.must.be.isolated.from.

the.gas.piping.system.by.closing.the.

manual.gas.shut-off.valve.during.any.

pressure.testing.of.the.gas.supply.piping.

at.pressures.equal.to.or.less.than..

3/8.psi.(10 .5”.w .c .).for.natural.gas,.or..

1/2.psi.(14”.w .c .).for.LP.gas .

Gas Supply

The.branch.gas.supply.line.to.the.water.

heater.should.be.clean.1/2”.black.steel.

pipe.or.other.approved.gas.piping.

material .
A.ground.joint.union.or.ANSI.design.

certified.semi-rigid.or.flexible.gas.

appliance.connector.should.be.installed.

in.the.gas.line.close.to.the.water.heater ..

The.National.Fuel.Gas.Code.(NFGC).

mandates.a.manual.gas.shut-off.valve:.See.

(NFGC).for.complete.instructions .
If.flexible.connectors.are.used,.the.

maximum.length.shall.not.exceed.36”.

and.must.meet.the.requirements.in.ANSI.

Z21 .24-Connectors.for.Gas.Appliances .
If.lever.type.gas.shut-offs.are.used,.

they..shall.be.T-Handle.type .
Compound.used.on.the.threaded.joints.of.

the.gas.piping.must.be.of.the.type.resistant.

to.the.action.of.LP.gas ..Use.compound.

sparingly.on.male.threads.only ..

Where.a.sediment.trap.is.not.incorporated.

as.part.of.the.appliance,.a.sediment.trap.

shall.be.installed.downstream.of.the.

equipment.shutoff.valve.as.close.to.the.

inlet.of.the.appliance.as.practical.at.the.

time.of.the.appliance.installation ..The.

sediment.trap.shall.be.either.a.tee.fitting.

with.a.capped.nipple.in.the.bottom.outlet.

or.other.device.recognized.as.an.effective.

sediment.trap .
Do.not.use.excessive.force.(over.31 .5.ft.

lbs .).in.tightening.the.pipe.joint.at.the.gas.

control.(thermostat).inlet,.particularly.if.

teflon.pipe.compound.is.used,.as.the.valve..

body.may.be.damaged .
The.inlet.gas.pressure.to.the.water.heater.

must.not.exceed.10 .5”.w .c ..for.natural.gas,.

or.14”.w .c ..for.LP.gas ..For.purposes.of.

input.adjustment,.the.minimum.inlet.gas.

pressure.(with.main.burner.on).is.shown.

on.the.water.heater.rating.plate ..If.high.or.

low.gas.pressures.are.present,.contact.your.

gas.supplier.for.correction .

WARNING: Never use

an open flame to test for

gas leaks, as property

damage, personal injury, or

death could result.

WARNING: Failure to

install a water heater

suitable for the altitude at

the location it is intended to

serve, can result in improper

operation of the appliance

resulting in property

damage and/or producing

carbon monoxide gas, which

could result in personal

injury, or death.

Содержание 43VP40E2









































Результаты поиска

Содержание 43VP40E2

Отзывы:

Похожие инструкции для 43VP40E2

Бренды по названию

Популярные бренды

PowerVent 43VP40E2, Инструкция по использованию и уходу

Результаты поиска

Содержание 43VP40E2

Отзывы:

Похожие инструкции для 43VP40E2

Бренды по названию

Популярные бренды