manualshive.com logo in svg

PowerVent 43VP40E2, Инструкция по использованию и уходу, Страница: 10 / 40

Поделиться
Скачать
PowerVent 43VP40E2 Скачать руководство пользователя страница 10

10

Installing the water heater.

A new combination temperature and pressure relief valve, complying with the Standard for Relief Valves 

and Automatic Gas Shut-Off Devices for Hot Water Supply Systems, ANSI Z21.22, is supplied and must 

remain in the opening provided and marked for the purpose on the water heater. No valve of any type 

should be installed between the relief valve and the tank. Local codes shall govern the installation of 

relief valves.

Relief Valve

The.pressure.rating.of.the.relief.valve.

must.not.exceed.150.PSI,.the.maximum.

working.pressure.of.the.water.heater.as.

marked.on.the.rating.plate ..
The.Btuh.rating.of.the.relief.valve.must.

equal.or.exceed.the.Btuh.input.of.the.

water.heater.as.marked.on.its.rating.plate .
Position.the.outlet.of.the.relief.valve.

above.a.suitable.open.drain.to.eliminate.

potential.water.damage ..Piping.used.

should.be.of.a.type.approved.for.hot.water.

distribution ..

The.discharge.line.must.be.no.smaller.

than.the.outlet.of.the.valve.and.must.

pitch.downward.from.the.valve.to.allow.

complete.drainage.(by.gravity).of.the.

relief.valve.and.discharge.line ..
The.end.of.the.discharge.line.should.not.

be.threaded.or.concealed.and.should.be.

protected.from.freezing ..No.valve.of.

any.type,.restriction,.or.reducer.coupling.

should.be.installed.in.the.discharge.line .

To Fill the Water Heater

Make.certain.that.the.drain.valve.is.

closed,.then.open.the.shut-off.valve.in.the.

cold.water.supply.line .
Open.each.hot.water.faucet.slowly.to.

allow.the.air.to.vent.from.the.water..

heater.and.piping ..
A.steady.flow.of.water.from.the.hot.water.

faucet(s).indicates.a.full.water.heater .

Do.not.allow.the.flammable.vapor.sensor.

to.become.submerged.in.water .

WARNING: The tank 

must be full of water before 

heater is turned on. The 

water heater warranty does 

not cover damage or failure 

resulting from operation 

with an empty or partially 

empty tank.

Condensation

Condensation.can.form.on.the.tank.

when.it.is.first.filled.with.water ..

Condensation.might.also.occur.with.a.

heavy.water.draw.and.very.cold.inlet.

water.temperatures ..
Drops.of.water.falling.on.the.burner.can.

produce.a.sizzling.or.pinging.sound .
This.condition.is.not.unusual,.and.will.

disappear.after.the.water.becomes.heated ..

If,.however,.the.condensation.continues,.

examine.the.piping.and.fittings.for.

possible.leaks .

Содержание 43VP40E2









































Отзывы:

Нет отзывов