manualshive.com logo in svg

PowerTec DC1080, Руководство пользователя

Поделиться
Скачать
PowerTec DC1080 Скачать руководство пользователя страница 8

MOTOR

The dust collector is assembled with motor and wiring 
installed. The electrical wiring schematic is shown in 
Figure 16.
The permanently split capacitor motor has the following 
specifications:
Horsepower (Peak HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Voltage   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120/240
Amp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10/5
Hertz  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Phase   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Single
RPM   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3450

ELECTRICAL CONNECTIONS

     WARNING

All electrical connections must be performed by a qualified 
electrician. Make sure tool is off and disconnected 
from power source while motor is mounted, connected, 
reconnected or anytime wiring is inspected. Motor 
and wires are installed as shown in wiring schematic 
(See Figure 16). Motor is assembled with approved, 
3-conductor cord to be used at 120 volts.

Figure 16

The power lines are inserted directly into the switch. The
green ground line must remain securely fastened to the 
frame to properly protect against electrical shock. The 
power supply to the motor is controlled by a single pole 
locking rocker switch.
•  Remove the key to prevent unauthorized use.

TO CONVERT TO 240V POWER SUPPLY

To convert the dust collector to 240V the switch box must 
be rewired and a new plug attached. A qualified electrician 
MUST inspect the switch box and new plug before the 
dust collector is connected to the power source.

The 240V power supply circuit must have a verified 
ground and meet these requirements: 
Circuit Type  . . . . . . . . . . . 220V/240V, 60 Hz, Single Phase
Circuit Size   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Amps
Plug Receptacle  . . . . . . . . . . . . . . . . . . . . . . . . NEMA 6-15

TO CONVERT

1.  Make sure the tool is unplugged.
2.  Open the switch box cover.
3.  Follow the 240V wiring diagram on the inside of the 

switch box cover. 

NOTE:

 The 240V wiring diagram 

is also in Figure 17. Call the customer service line at 

847-780-6120 

for assistance if needed.

Figure 17

4.  After rewiring make sure all wire nuts are tight and 

use electrical tape to secure them in place.

5.  Replace the plug on the existing power cord with 

a NEMA 6-15 plug. The plug must be plugged into 
matching outlet that is properly installed and grounded 
in accordance with all local codes and ordinances. 

6.  Have the wiring inspected by a qualified electrician.
7.  Replace the switch box cover.

Figure 18

Properly Grounded Outlet

Grounding Prong

240 NEMA 
6-15 Plug

6

ASSEMBLY

Содержание DC1080

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды