PowerTec DC1080 Скачать руководство пользователя страница 5

Страница: 5 / 16

ASSEMBLY

INSTALLATION

Refer to Figures 2 - 14

CAUTION

Do not attempt assembly if parts are missing.
Call the Customer service line to obtain replacement parts.

WARNING

Do not operate dust collector until completely assembled.
Do not operate this tool until you have completely read
and understood this manual.

NOTE:

After unit is assembled dispose of all packaging

material in an environmentally safe way.

Tools required for assembly:

• 10-12 mm Wrench
• Phillips Screwdriver

WARNING

Ensure the dust collector is unplugged before
assembling

1. Place the four casters through the bottom of the base

plate. Secure with the 5/16-18 washers and 5/16"
nuts, use the 12 mm wrench to tighten hardware.

Figure 2

Caster

Nut

Washer

2. Lay the collection body upside down on a

protective surface as shown.

Figure 3

Collection Body

3. Attach the two rectangular supports to the collection

body using the 5/16 x 1/2" hex head screws, use the
12 mm wrench to tighten hardware.

Figure 4

Collection
Body

Rectangular
Supports

5/16 X 1/2" Hex
Head Screws

4. Attach the round support to collection body with the

5/16 x 1/2" hex head screws, use the 12 mm wrench
to tighten hardware.

Figure 5

Round
Support

5/16 X 1/2" Hex
Head Screws

5. Lay the collection body assembly on its side.

Figure 6

Collection
Body

6. Use 5/16 x 1/2" hex head screws to attach the

collection body assembly to the base assembly as
shown. Use the 12 mm wrench to tighten hardware.

Round
Support

Base
Assembly

Rectangular
Supports

Figure 7

Содержание DC1080

















Результаты поиска

Содержание DC1080

Отзывы:

Бренды по названию

Популярные бренды

PowerTec DC1080, Руководство пользователя

Результаты поиска

Содержание DC1080

Отзывы:

Бренды по названию

Популярные бренды