4/8
4
、
Press the corresponding
key and
key to change the parameter value or selection parameter number;
5
、
At last press
key to exit parameter setting mode,return to sewing work mode.
1 0 0
100~800 200
Minimum speed
1 0 1
200~5000 3500
Maximum speed
1 0 2
200~5000 3000
Constant-stitch sewing speed
1 0 5
100~500 250
Trimming speed
1 0 7
1~9 2
Stitch numbers for soft start
1 0 8
100~800 200
Soft start speed
1 1 0
200~2200 1800
Start back tacking speed
1 1 1
200~2200 1800
End back tacking speed
1 1 2
200~2200 1800
Bar tacking speed
1 1 3
1~70 24
Stitch balance for start back tacking No.1
1 1 4
1~70 20
Stitch balance for start back tacking No.1
1 1 5
1~70 24
Stitch balance for end back tacking No.3
1 1 6
1~70 20
Stitch balance for end back tacking No.4
1 1 7
1~100 90
Stitch balance for back tacking speed @(P107 - Tacking stitches A = 1)
1 1 8
1~100 30
Stitch balance for back tacking speed @(P107 = Tacking stitches A)
1 1 B
0~4 0
Start and end back tacking type (CD and AB)
0
：
B->AB->ABAB->none 1
：
B->none 2
：
B->AB->none 3
：
AB->none 4
：
AB->ABAB->none
1 1 C
0~9999 0
Tens digit for each segment of A/B/C/D
1 1 D
0~9999 0
Tens digit for each segment of E/F/G/H
1 1 E
0~9999 0
Tens digit for each segment of A/B/D
1 1 F
0~359 0
Back tacking under angle control
1 3 0
0
／
1
／
2
／
3 2
Speed curve adjustments:
0
：
ramp curve 1
：
polygonal curve. 2
：
quadric curve 3
：
S-type curve
1 3 1
200~4000 3000
The turning point speed of two segment curve.
1 3 2
0~1024 800
The turning point sampling voltage of the pedal when two segment curve (Between
parameter 138 and 139)
1 3 3
1
／
2 1
The type of polygonal curve: 1: square 2
：
rooting
1 3 4
0~1024 90
Trimming point of pedal
1 3 5
0~1024 300
Footer lifting point of pedal
1 3 6
0~1024 460
Neutral point of pedal
1 3 7
0~1024 480
Motor running point of pedal in low speed.
1 3 8
0~1024 580
Accelerated point of pedal
1 3 9
0~1024 962
Max speed point of pedal
Figure 4-1 shows the specific setting
method
1 3 A
0~800 100
The running delay time of footer lifting
1 4 0
0
／
1 1
Soft start at the first cycle of power ON. 0: disable 1: enable
1 4 1
0
／
1 1
Auto bar tacking function: 0: disable 1: enable
1 4 2
0
／
1 0
Bar tacking mode selection:
0
：
Juki mode. Active when motor stop or running. 1
：
Brother mode. Active only when
motor running.