manualshive.com logo in svg

Powermatic 1150HD, Инструкция по эксплуатации

Поделиться
Скачать
Powermatic 1150HD Скачать руководство пользователя страница 16

16

The 1 HP Baldor motor is wound with "Inverter Spike Resistant" magnet wire to give extended motor life when

used with inverter drives.  The motor is also specially balanced to reduce noise and minimize vibration.

The A.C. inverter does not require any programming; it is pre-programmed from the factory.  The buttons on the

face of the inverter should NEVER be pushed at any time.  Use ONLY the controls on the front of the head

assembly.

POWER CONNECTION - ELECTRONIC VARIABLE SPEED

The 1150HD Drill Press will operate on single or three phrase, 230V or 460V, depending on the inverter, without

any adjustments or programming.  For single phase power, connect hot leads to L1 and L2.  For three phrase

power, connect hot leads to L1, L2 and L3 as shown in the wiring diagram on page 39.  Remember to always

connect the ground lead.

Before connecting to the power source make sure the ON/OFF switch is in the OFF position, and turn the speed

dial counterclockwise.  If the switch is in the ON position when the power is connected, the inverter will trip out.

If this happens, disconnect power, turn switch OFF, wait thiry seconds and then reconnect power.

NOTE:  If there is a power outage while operating the 1150HD Drill Press, turn the switch to the OFF position,

disconnect power source, wait thiry seconds then reconnect power source and resume normal operation.

FOOT SWITCH OPERATION 

(Optional - Model 1150HD only )

The optional foot switch is used only for reversing the spindle in tapping operations.

Before using the foot switch, place the control switch in the FWD position.

When performing a tapping operation and the tap needs to be reversed or retracted out of a hole, press the

foot switch and hold it down. The spindle will ramp down and immediately reverse direction. Once the tap has

completely exited or retracted from the hole, release the foot switch and the spindle will ramp down and

immediately return to forward rotation.

Содержание 1150HD













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды