Power-Tronics XR5B-400 Скачать руководство пользователя

Страница: 18 / 21

Application Troubleshooting

Problem:

Possible Cause

No Voltage

1 3 5 7 9 11 13 15 20

Pulsating Voltage

4 5 6 12 16

Flickering Voltage

4 6 7 14

High Voltage

6 7 8 9 12 13 17 18 20

Voltage Drop on Load

5 8 10 12 16

Low Voltage

5 8 12 13

Poor Voltage Regulation

2 4 10 12 13 16

No Voltage Control

13 19 20

Possible Causes:

1. Residual input voltage to the voltage regulator is below 3.5vac or fuses are open in the regulator.

2. Unbalanced generator load.

3. Open exciter field or defective generator.

4. Non linear load or defective connection in exciter field.

5. Open diode in exciter or shorted rotor in generator.

6. Stability adjustment is not properly adjusted or loose component in voltage regulator.

7. Loose wiring connections.

8. Input voltage to regulator is too low.

9. Exciter field is grounded.

10. Non linear load, stability control too far clockwise, or wrong selection for regulator hookup.

11. Exciter fields are reversed.

12. Wrong selection of regulator wiring configuration.

13. Defective voltage regulator.

14. SCR or Inverter drive effecting generator waveform.

15. Regulator needs external flashing circuit.

16. Isolation transformer is too small.

17. Isolation transformer is needed.

18. Exciter fields are not isolated from other circuits.

19. Input and field circuit are being fed by a common cable or conduit.

20. Incorrect hookup or wiring.

Содержание XR5B-400






















Результаты поиска

Содержание XR5B-400

Отзывы:

Похожие инструкции для XR5B-400

Бренды по названию

Популярные бренды

Power-Tronics XR5B-400, Руководство пользователя

Результаты поиска

Содержание XR5B-400

Отзывы:

Похожие инструкции для XR5B-400

Бренды по названию

Популярные бренды