background image

Page 22  — English

WARRANTY

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The U.S. EPA, Environment Canada,  and OWT Industries, Inc., 
are pleased to explain the evaporative emission control system’s 
warranty on your small off-road equipment. New equipment that 
uses small off-road engines must be designed, built, and equipped 
to meet the stringent evaporative standards. OWT Industries, Inc., 
must warrant the evaporative emission control system on your 
small off-road equipment for the period listed below, provided 
there has been no abuse, neglect or improper maintenance of 
your equipment. 
Your evaporative emission control system may include parts such 
as: carburetors, fuel tanks, fuel line, fuel caps, valves, canisters, 
filters, vapor hoses, clamps, connectors, and other associated 
components. 

MANUFACTURER’S WARRANTY COVERAGE:

This evaporative emission control system is warranted for three 
years. If any evaporative emission-related part on your equipment is 
defective, the part will be repaired or replaced by OWT Industries, Inc. 

OWNER’S WARRANTY RESPONSIBILITIES:

  As the small off-road equipment owner, you are responsible 

for performance of the required maintenance listed in your 
operator’s manual. OWT Industries, Inc., recommends that you 
retain all receipts covering maintenance on your small off-road 
equipment, but OWT Industries, Inc.,  cannot deny warranty 
solely for the lack of receipts.

  As the small off-road equipment owner, you should, however, 

be aware that OWT Industries, Inc., may deny you warranty 
coverage if your small off-road equipment or a part has failed 
due to abuse, neglect, or improper maintenance or unapproved 
modifications.

  You are responsible for presenting your small off-road equip-

ment to a OWT Industries, Inc., distribution center or service 
center as soon as the problem exists. The warranty repairs 
should be completed in a reasonable amount of time, not to 
exceed 30 days.

If you have a question regarding your warranty coverage, you 
should contact OWT Industries, Inc., at 1-877-617-3501.

DEFECTS WARRANTY REQUIREMENTS:

(a) The warranty period begins on the date the equipment is de-

livered to an ultimate purchaser. 

(b) General Evaporative Emissions Warranty Coverage. The equip-

ment must be warranted to the ultimate  purchaser and any 
subsequent owner that the evaporative emission control system 
when installed was: 

  (1) Designed, built, and equipped so as to conform  with all 

applicable regulations; and 

  (2) Free from defects in materials and workmanship that cause 

the failure of a warranted part for a period of three years.

(c) The warranty on evaporative emissions-related parts  will be 

interpreted as follows:

  (1) Any warranted part that is not scheduled for replacement 

as required maintenance in the written instructions must be 
warranted for the warranty period defined in subsection (b)
(2). If any such part fails during the period of warranty cov-
erage, it must be repaired or replaced by the manufacturer 
issuing the warranty. Any such  part repaired or replaced 

under the warranty must be warranted for a time not less 
than the remaining warranty period. 

  (2) Any warranted part that is scheduled only for regular inspec-

tion in the written instructions must be warranted for the 
warranty period defined in subsection (b)(2). A statement in 
such written instructions to the effect of “repair or replace as 
necessary” will not reduce the period of warranty coverage. 
Any such part repaired or replaced under warranty must be 
warranted for a time not less than the remaining warranty 
period. 

  (3) Any warranted part that is scheduled for replacement as 

required maintenance in the  written instructions must be 
warranted for the period of time prior to the first scheduled 
replacement point for that part. If the part fails prior to the 
first scheduled replacement, the part must be repaired or 
replaced by the manufacturer issuing the warranty. Any such 
part repaired or replaced under warranty must be warranted 
for a time not less than the remainder of the period prior to 
the first scheduled replacement point for the part. 

  (4) Repair or replacement of any warranted part  under the 

warranty provisions of this article must be performed at no 
charge to the owner at a warranty station. 

  (5) Notwithstanding the provisions of subsection  (4) above, 

warranty services or repairs must be provided at distribution 
centers that are franchised to service the subject equipment. 

  (6) The owner must not be charged for diagnostic labor that 

leads to the determination that a warranted part is in fact 
defective, provided that such diagnostic work is performed 
at a warranty station. 

  (7) Throughout the evaporative emission control system’s war-

ranty period set out in subsection (b)(2), the manufacturer 
issuing the warranty must maintain a supply of warranted 
parts sufficient to meet the expected demand for such parts. 

  (8) Manufacturer approved replacement parts must be used in 

the performance of any warranty maintenance or repairs and 
must be provided without charge to the owner. Such use 
will not reduce the warranty obligations of the manufacturer 
issuing the warranty. 

  (9) The use of any add-on or modified parts will be grounds 

for disallowing a warranty claim made in accordance with 
this article. The manufacturer issuing the warranty will not 
be liable under this Article to warrant failures of warranted 
parts caused by the use of an add-on or modified part. 

 

EMISSION WARRANTY PARTS LIST:

1)  Fuel Tank
2)  Fuel Cap
3)  Fuel Line
4)  Carbon Canister
5)  Vapor Hoses
6)  Hose Clamps
7)  Hose Connectors
8)  Vapor/Fuel Check Valve
Written instructions for the maintenance and use of the evaporative 
emissions control system by the owner shall be furnished with all 
new small off-road equipment.

OWT INDUSTRIES, INC., FEDERAL EMISSION CONTROL WARRANTY STATEMENT

Содержание PS905000A

















































Отзывы: