background image

 

12 

Cutting large sheets 

 

Large sheet or boards require support to prevent bends or sags. If you attempt to cut without levelling 

and properly supporting the work piece, the blade will tend to bind, causing kickback. 

 

Support the panel or board close to the cut. Be sure to set the blade adjustment so that you can cut 

through the material without cutting into the table or workbench.  

Suggestion: use two by fours to support the board or panel to be cut. If the piece is too large for the 

workbench, use the floor with the two-by fours supporting the wood. 

 

Laser line generator  

 

 

 

 

WARNING: 

Do not stare directly at the laser beam, do not deliberately aim the beam at 

personnel and ensure that it is not directed towards the eye of a person for longer than 0.25s. 

 

 

 

When you make the line of the cut on the work piece, the laser line generator can help you get 

better alignment. 

 

The laser generator switch is located at the front of the safety lock button for the mechanical plunge stop. 

Turn on: Press the laser generator switch to “I” position, the laser generator (1) works. 

Turn off: Press the switch to 

O

 position. 

1.

 

Make sure line of the cut is on the work piece. 

2.

 

Adjust the depth of cut as required. 

3.

 

Plug in the machine and start the motor. 

4.

 

When the blade is at its maximum speed (approximately 5 seconds), place the saw on the work-piece. 

5.

 

Switch on the laser generator from the laser aperture using the laser generator switch. 

6.

 

Align the beam with the mark on the work-piece and slowly push the saw forward using both hands, 

keeping the red-light beam on the mark. 

7.

 

Switch off the laser beam after completion of the cut. 

 

 

 

 

 

 

 

 

 

 

Содержание PS4405

















Отзывы: