manualshive.com logo in svg

Power-Pole Blade, Инструкция по установке и эксплуатации

Поделиться
Скачать
Power-Pole Blade Скачать руководство пользователя страница 8

NOTE:  

Each Power-Pole anchor is preprogrammed as a single unit. When 
using only one anchor do not program as a port or starboard. 

1.  Determine which HPU controls the starboard side Power-Pole anchor 

using the UP & DOWN buttons on both HPUs. 

FIG. 19

2.  Locate the C-Monster PROGRAM button on the top of the starboard 

HPU. Depress and hold it for 6 seconds until the LED flashes 

RED

 and 

2 chimes are heard followed by a single beep. 

FIG. 20

 

3.  Next, depress and release the UP button. The LED will flash 

RED

 1 time 

with a single beep indicating that the HPU has been assigned as the 
starboard side unit. Press and release the PROGRAM button to save 
and exit. The LED will flash 

RED

 1 time with a single beep followed by 

2 consecutive beeps.

4.  On the port side HPU, repeat Step 2 to enter programming mode. 

Next, depress and release the DOWN button on the HPU. The LED 
will flash 

RED

 twice with 2 consecutive beeps indicating that the 

programming has been completed successfully and the HPU has been 
assigned as the port side unit. Press and release the PROGRAM button 
to save and exit. The LED will flash 

RED

 2 times with a double beep 

followed by 2 consecutive beeps.

NOTE:  

For additional menu settings please refer to the Operation Section.

DOWN button

UP button

LED

STEP

6

Programming Dual Units

Figure 19

Figure 20

PROGRAM button

LED

Содержание Blade





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды