manualshive.com logo in svg

Power-Pole Blade, Инструкция по установке и эксплуатации

Поделиться
Скачать
Power-Pole Blade Скачать руководство пользователя страница 20

©2017 all rights reserved. Power-Pole Shallow Water Anchor U.S. Patent No. 6,041,730

General Statement

Warning: Changes or modifications to this device not expressly approved by JL Marine Systems, Inc. could void the user’s authority to 

operate the equipment.

FCC Specific Statement

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the 

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This 

equipment generate, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, 

may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular 

installation. If this equipment does cause harmful interference to radio or television receptio, which can be dteremined by turning the 

equipment off and on, he user is encouraged to try to correct the interferecne by one or more of the following measures:

 

• Reorient or relocate the receiving antenna.

 

• Increase the separation between the equipment and receiver

 

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

 

• Consult the dealer or an experienced radio/TV technician for help

RF Exposure

ENGLISH: This equipment complies with radiation exposure limits set forth for an uncontrolled environment. This equipment is in direct 

contact with the body of the user under normal operating conditions. The transmitter must not be co-located or operating in conjuction 

with any other antenna or transmitter.
FRENCH: Cet équipment est conforme aux limites d’exposition aux radiations dans un environment non controle. Cet équipment est en 

contact direct avec le corps de l’utilisateur dans des conditions de fonctionnement normales. Cet émetteur ne doit pas être co-localisées 

ou opérant en conjunction avec tout autre antenne ou transmetteur.

ENGLISH: This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two 

conditions: (1) this device may not cause interference, and (2) this device must not accept any interference, including interference that 

may cause undesired operation of the device.
FRENCH: Le présent est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de license. L’exploitation est 

autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter 

tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.  

Man-owner-internat-122016

9010 Palm River Road, Tampa, Florida 33619

Phone 1+(813) 689-9932  Fax 1+(813) 689-8883

www.power-pole.com

CAUTION:

Do not use the Power-Pole  shallow water anchor as your primary anchorge. Never leave 

your boat unattended while anchored solely with the Power-Pole shallow water anchor.

Содержание Blade





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды