2
Power-Flo Pumps & Systems • 877-24PUMPS • www.powerflopumps.com
PFSE .05, .75 & 1HP
Sewage Pumps
General Safety Information
® Power-Flo is a registered trademark of Power-Flo Technologies Inc. Other brand and product names are trademarks or registered trademarks of their respective
holders. Alteration Rights Reserved.
5/08, 6/13, 4/14, 8/17, 9/2020, 1/2021
Before installation, read the following
instructions carefully. Failure to follow
instruction and Safety information could
cause serious bodily injury, death and/or
property damage. Each Power-Flo pump is
individually factory tested to insure proper
performance. Closely following these
instructions will eliminate potential operating
problems, assuring years of trouble-free
service.
“
Danger” indicates
an imminenty
hazardous situation which, if not avoided,
WILL result in death or serious injury.
“Warning” indicates
an imminenty
hazardous situation which, if not avoided,
MAY result in death or serious injury.
“Caution” indicates
an potentially
hazardous situation which, if not avoided,
MAY result in minor or moderate injury.
IMPORTANT - Power-Flo Pumps and
Systems is not responsible for losses, injury
or death resulting from failure to observe
these safety precautions, misuse, abuse or
misapplication of pumps or equipment.
ALL
RETURNED
PRODUCTS MUST BE
CLEANED, SANITIZED,
OR DECONTAMINATED
PRIOR TO SHIPMENT, TO
INSURE EMPLOYEES WILL NOT BE EXPOSED
TO HEALTH HAZARDS IN HANDLING SAID
MATERIAL. ALL APPLICABLE LAWS AND
REGULATIONS SHALL APPLY.
Installation, wiring,
and junction
connections must be in accordance with
the National Electric Code and all applicable
state and local codes. Requirements may
vary depending on usage and location.
Installation and
servicing is to be
conducted by qualified personnel only.
Keep clear of suction
and discharge
openings.
Do not
insert fingers in
pump with power connected.
Always wear eye
protection when
working on pumps. Do not wear loose
clothing that may become entangled in
moving parts
Pumps build up heat
and pressure during
operation. Allow time
for pumps to cool
before handling or
servicing.
This pump is
not
intended for use
in swimming pools or water
installations where human
contact with pumped fluid.
Risk of electric shock.
To reduce risk of
electric shock, always disconnect
pump from power source before
handling.
Lock out power & tag.
Do not
us these
pumps in water over
104˚F. High temperature units PFSE51HT
200˚F.
Do not
exceed manufactures
recommended maximum performance, as
this could cause the motor to overheat.
Do not
lift, carry or
hang pump by the
electrical cables. Damage to the
electrical cables can cause shock,
burnes or death.
Never
handle
connected power cords with wet hands. Use
appropriate lifting device.
Ground Fault Circuit
Interrupter (GFCI)
to be used with plug-in type power cord.
Sump and sewage
pumps often handle
materials which could cause illness or disease.
wear adequate protective clothing when
working on a used pump or piping. Never
enter a basin after it has been used.
Failure to permanently
ground the pump,
motor and controls before
connecting to power can cause
shock, burns or death.
These pumps are NOT
to be installed in
locations classified as hazardous in
accordance with the National
Electric Code, ANSI/NFPA 70.
The Uniform Plumbing
Code (UPC) states that
sewage systems shall have an audio and
visual alarm that signals a malfunction of
the systems that is required to reduce the
potential for property damage.
IMPORTANT!
Prior to installation, record Model
Number, MFG Date, Amps, Voltage, Phase
and HP, from pump name plate for future
reference. Also record the Voltage and
Current Readings at Startup:
1 Phase Models
Amps:
Volts:
3 Phase Models
Amps L1-2:
Volts L1-2:
Amps L2-3:
Volts L2-3:
Amps L3-1:
Volts L3-1:
Model Number: ____________________
MFG Date: ____________
PHASE: ______ HP: _________________
WARNING:
CANCER AND REPRODUCTIVE HARM-
WWW.P65WARNINGS.CA.GOV
