Poulan Pro 438511 Скачать руководство пользователя страница 18

Страница: 18 / 28

SERVICE AND ADJUSTMENTS

TO REMOVE MOWER (See Fig. 15)

Mower will be easier to remove from the right side of trac-

tor.
• Place attachment clutch in “DIS EN GAGED” position.
• Move attachment lift lever forward to low er mower to

its lowest po si tion.

• Roll belt off engine pulley.
•

Remove small retainer spring, and remove clutch spring

off pulley bolt.

•

Remove large retainer spring, slide col lar off and push

housing guide out of brack et.

• Disconnect anti-swaybar from chas sis bracket by re-

mov ing re tain er spring.

• Disconnect suspension arms from rear deck brackets

by removing retainer springs.

• Disconnect front links from deck by re mov ing retainer

springs.

•

Raise lift lever to raise suspension arms. Slide mower

out from under tractor.

IMPORTANT:

IF AN ATTACHMENT OTHER THAN THE MOWER

DECK IS TO BE MOUNTED ON THE TRAC TOR, REMOVE THE

FRONT LINKS AND HOOK THE CLUTCH SPRING INTO SQUARE

HOLE IN FRAME.

TO INSTALL MOWER (See Fig. 15)

• Raise attachment lift lever to its high est position.
•

Slide mower under tractor with deflector shield to right

side of tractor.

• Lower lift lever to its lowest po si tion.
• Connect front links to mower deck and secure with

retainer springs..

• Connect suspension arms to rear deck brackets and

secure with retainer springs.

• Connect anti-swaybar to chassis bracket and secure

with retainer spring.

•

Push clutch cable housing guide into bracket, slide col-

lar onto guide and secure with large retainer spring.

•

Place flat washer and clutch spring on idler pulley bolt

and secure with small retainer spring.

• Install belt onto engine pulley.

SUSPENSION

ARMS

RETAINER SPRINGS

(BOTH SIDES)

RETAINER SPRING

ANTI-SWAY BAR

HOUSING GUIDE

FRONT LINK

COLLAR

ENGINE PULLEY

LARGE

RETAINER

SPRING

CLUTCH SPRING

SMALL RETAINER SPRING

BRACKET

SQUARE HOLE

Fig. 15

DEFLECTOR SHIELD

SMALL RETAINER SPRING

CLUTCH SPRING

FLAT WASHER

WARNING: TO AVOID SE RI OUS IN JU RY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:

•

Depress clutch/brake pedal fully and set parking brake.

•

Place gearshift lever in neutral position.

•

Place attachment clutch in “DISENGAGED” position.

•

Turn ignition key to “STOP” and remove key.

•

Make sure the blades and all moving parts have completely stopped.

•

Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

Содержание 438511





























Результаты поиска

Содержание 438511

Отзывы:

Похожие инструкции для 438511

Бренды по названию

Популярные бренды

Poulan Pro 438511, Руководство оператора

Результаты поиска

Содержание 438511

Отзывы:

Похожие инструкции для 438511

Бренды по названию

Популярные бренды