Potterton Sirius two WH, Инструкция по эксплуатации

Страница: 15 / 32

15
IN
S
T
A
L
L
E
R
S
e
c
ti
o
n
(e
n
)
7108686.02 (1-11/12)
(a) (b)
ZONE 1 HEATING PARAMETERS
(main zone)
Factory
setting
Minimum Maximum
P01 700 * Operating mode (0=Frost Protection, 1=Timed, 3=T.comfort) - 3 0 3
P02 712 * Reduced ambient temperature °C 16 4 35
P03 720 * “Kt” curve slope - 1,5 0,1 4
P04 721 * “Kt” curve drift - 0 - 4,5 4,5
P05 726 * “Kt” curve adaptation (0=off) - 1 0 1
P06 740 Flow temperature setpoint (minimum value) °C 25 8 80
P07 741 Flow temperature setpoint (maximum value) °C 80 25 80
P08 742 * Enable modulating temperature if set = “ --- ” °C 80 25 80
P09 750 * Room influence (“---” = disabled) % 50 1 100
P10 834 * Opening/Closing speed of mix valve S 180 30 873
ZONE2 HEATING PARAMETERS
(with accessory Expansion Unit)
P11 1000 * Operating mode (0= Frost Protection, 1=Timed, 3=T.comfort ) °C 3 0 3
P12 1010 * Comfort room temperature °C 20 4 35
P13 1012 * Reduced room temperature °C 16 4 35
P14 1020 * “Kt” curve slope - 1,5 0,1 4
P15 1021 * “Kt” curve drift - 0 - 4,5 4,5
P16 1026 * “Kt” curve adaptation (0=off) - 1 0 1
P17 1040 Flow temperature setpoint °C 25 8 80
P18 1041 Flow temperature setpoint (maximum value) °C 80 25 80
P19 1042 * Enable modulating temperature if set = “ --- ” (flow temp. setpoint if P63=0) °C 80 25 80
P20 1050 * Room influence (“---” = disabled) % 50 1 100
P21 1134 * Opening/Closing speed of mix valve s 180 30 873
DHW PARAMETERS
P22 1620
Operating mode in DHW (with Remote Control)
- 0 0 2 0=always enabled, 1=according to hourly heating programme,
2= according to hourly DHW programme.
P23 1640
Anti-legionella function Disabled
- 0 0 1
0=disabled, 1=periodic (depending on P24)
P24 1641
Periodic anti-legionella function enable (
only if P23 =1)
- 7 1 7
1=daily, 2..6=intervals of 2..6 days, 7=once a week
P25 1663 Circulation temperature setpoint (additional DHW pump) °C 45 8 80
P26 5470 Preheating time for DHW circuit (1=10’ -- 144=1440’) min 0 0 144
BOILER PARAMETERS
P27 2243 Minimum boiler off time min 3 0 20
P28 2217 Frost Protection setpoint °C 5 -20 20
P29 2250 Pump post-circulation time min 3 0 240
P30 2441 Max. fan speed (heating) rpm xxx 0 8000
P31 2455 Minimum boiler off differential °C 10 0 20
SOLAR PLANT PARAMETERS (with accessory Expansion Unit)
P34 3810 Temperature - on differential °C 8 0 40
P35 3811 Temperature - off differential °C 4 0 40
P36 3830 Collector start function (“---” = disabled) min --- 5 60
P37 3850 Solar panel manifold overheating protection (“---“ = disabled) °C --- 30 350
P38 5050 DHW charging temperature max °C 65 8 95
P39 5051 Maximum temperature of storage tank °C 90 8 95
CONFIGURATION
P40 5700
Not used (Do NOT change this parameter) - --- --- ---
P41 5710
Zone 1 heating circuit (1=enabled) -
1
0 1
P42 5715
Zone 2 heating circuit (1=enabled) -
0
0 1
P43 5730
DHW sensor (1=Tank sensor, 2=Thermostat, 3=instantaneous sensor)
1
1 3
P44 5890
Not used (Do NOT change this parameter) -
33
0 43
P45 5931 *
BX2 sensor input (first auxiliary sensor – section 11) -
0
0 19
P46 5932 *
BX3 sensor input (second auxiliary sensor – section 11) -
0
0 19
P47 5977 *
Input H5 (multifunction input – 18=Room thermostat) -
18
0 32
P48 6020 * Configuration of accessory Expansion Unit - 0 0 7
P49 6024 Function input EX21 module 1 (configuration of HC Safety Thermostat) - 0 0 1
P50 6046 Function input H2 module 1 (multifunction input) - 0 0 58
P51 6097 Sensor type collector (1= NTC, 2= Pt 1000) - 2 1 2
P52 6110 Building time constant h 15 0 50
P53 6220
Software version -
---
0 99
P54 6600
LPB device address - 1 16
P55 6601
LPB segment address - 0 14
P56 6640
Clock time source - 0 3