Potterton PROMAX 24 Скачать руководство пользователя страница 40

Страница: 40 / 56

Fig. 22

4.10

Burner

. Remove the fan/manifold assembly - see

Section 4.6.

2. Undo the screws securing the spacer to
the cover.

3. Withdraw the burner from the cover and
replace with the new one.

4. Replace the burner gas

et.

. Reassemble in reverse order.

4.11

Insulation

. Remove the electrode leads, noting their

positions. Also remove the electrodes.

2. Undo the screws securing the cover to the
heat exchanger. Draw the cover assembly
away.

3. Remove the cover insulation piece.

4. Fit the new insulation carefully over the
burner and align it with the slots for the
electrodes.

. The rear insulation is retained by a screw

and large washer, remove these and draw
the insulation out of the heat exchanger.

6. Examine the cover seal and replace if
necessary.

Heat

Exchanger

Rear

Insulation

over

Insulation

Seal

Manifold

Spar

Electrode

Sensing

Electrode

eads

Venturi

over

Burner

Gas

Extension

iece

Manifold

Venturi

© Baxi Heating UK Ltd 2015

Содержание PROMAX 24

























































Результаты поиска

Содержание PROMAX 24

Отзывы:

Potterton PROMAX 24, Инструкция по установке и обслуживанию, Страница: 40 / 56

Результаты поиска

Содержание PROMAX 24

Отзывы: