Potterton PROMAX 24 Скачать руководство пользователя страница 38

Страница: 38 / 56

4.5

Gas Valve

. Turn the gas coc

OFF and disconnect

the electrical plug.

ull off the earth lead and sensing pipe.

3. Undo the nuts on the venturi inlet pipe
and valve inlet pipe. Remove the gas valve.

4. Examine the sealing washers, replace if
necessary.

. Reassemble in reverse order, ensuring

the sealing washers are in place.

PORTANT:

The

must be chec

and adjusted (see

ommissioning

hec

on p.3

and 32).

4.6

Fan

. Remove the air box front cover.

2. Undo the nut on the gas inlet pipe to the
venturi and pull the sensing pipe off the fan.
Examine the sealing washer and replace if
necessary.

3. Undo the screws securing the manifold to
the extension piece.

artially remove the manifold and fan

assembly, being careful to retain the injector
in the venturi. Disconnect the fan electrical
plugs before completely removing the
assembly.

. Undo the screws securing the fan to the

venturi and fit the new fan, replacing the seal
if necessary.

6. Examine the gas

et behind the manifold

and replace if necessary.

. Reassemble in reverse order, ensuring

that the injector is in place and the sensing
pipe is connected to the fan.

Fig. 20

Gas Valve

Valve

Inlet

ipe

Gas Feed

Elbow

Earth

ead

Sensing

ipe

Venturi Inlet

ipe

over

Fan

Venturi

Manifold

Burner

Gas

Sensing

ipe

Injector

Sealing Washer

© Baxi Heating UK Ltd 2015

Содержание PROMAX 24

























































Результаты поиска

Содержание PROMAX 24

Отзывы:

Potterton PROMAX 24, Инструкция по установке и обслуживанию, Страница: 38 / 56

Результаты поиска

Содержание PROMAX 24

Отзывы: