Potterton PROMAX 24 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 56

Potterton PROMAX 24 Скачать руководство пользователя страница 39

Fig. 2

1

4.7

Igniter

1

. Remove the air box front cover.

2. Disconnect the igniter feed plug and the
electrode leads, noting their positions.

3. Undo the screw securing the brac

k

et to the

boiler.

4. Remove the igniter and transfer the
brac

k

et to the new component.

5

. Reassemble in reverse order.

4.8

Spark and Sensing Electrodes

1

. Disconnect the electrode leads, noting

their positions.

2. Remove the retaining screws securing
each of the electrodes to the combustion box
cover and remove the electrodes.

3.

C

hec

k

the condition of the sealing gas

k

ets

and replace if necessary. Reassemble in
reverse order.

4.9 Overheat Thermostat

Re-assemble all parts in reverse order.

1

.

P

erform 4.

1

General Access.

2. Disconnect electrical connections and
unscrew the thermostat.

P

olarity of the

wires is not important.

Igniter

Igniter Feed

P

lug

Electrode

L

eads

Brac

k

et

Spar

k

Electrode

Sensing

Electrode

Electrode

L

eads

39

© Baxi Heating UK Ltd 2015

«
...
37
38
39
40
41
...
»

Содержание PROMAX 24

























































Отзывы:

Нет отзывов