17
Liability Limitation
●
Installation and maintenance
We recommend that you inquire about product installation, maintenance and repair USER from the official USER
center and agent office.
POSBANK takes no responsibility for malfunctions or system errors occurring after USER and/or system check carried
out by unofficial USER providers.
●
High frequency appliances
This product is qualified by FCC, CE and KC compliances, and is thus governed by these qualifications’ safety
regulations.
However, the product can affect and be affected by other high frequencies generated around it. As such, POSBANK
does not consider liability for any system error or disorder due to this issue.
●
Electronic noise emitting equipment
We recommend using the product away from electronic noise emitting equipment such as heaters, motors, fluorescent
lights, TVs etc. as it may cause interruption or interference with normal operation.
●
Installation location
For optimal performance, the product should be kept in an environment of lower than 65% humidity and in a
temperature of 10 ~ 30
℃
. Please also keep away from direct sun-light.
●
Cleaning procedure
Cleaning with chemical based products (in particular those containing benzyl or chemical thinning agents) can damage
the exterior surfaces of the product. We recommend using a soft damp cloth and wiping gently, taking particular care
when dealing with the LCD display screen.
●
Product limitations
1.
The use of this product for anything other than POS tasks is strictly prohibited.
The product is not supported for regular PC and interface operation.
2.
This product is for business use only, and not for usage in the home.
3.
Both hardware and software are both fully configured.
4.
Normal operating is guaranteed on a steady power connection.
Содержание ANYSHOP PRIME
