EN
6
3.5.2.6
Stopping the winch.
1)
Gradually release the tension to gradually lower the
winch towards the ground;
2)
Press the on/off button.
4
Maintenance
4.1
Cleaning.
When your work is complete, clean and dry the winch.
4.2
Lubrification.
The gearbox is lubricated in the factory and thus should not require
lubrication or maintenance. If oil losses become apparent, check
the oil level by placing the winch on a level surface and unscrew the
cap. Use an 8 mm hexagonal key.
When tipping the winch forwards, a little oil may escape through the
hole. If required, you can add SAE80W90EP gear oil.
4.3
Charger and battery.
4.3.1
Charger.
4.3.1.1 Charging.
If the battery has been stored with little charge or with no charge for
a long period, the charger enters restart mode which takes 20 hours
for the battery to be fully charged.
This prolongs the life of the battery. Once fully charged, standard
charging is available next time.
Any discharged battery requires a cooling period which is
mentioned in the battery user manual.
�
Plug the charger into the mains.
�
Insert the battery into the charger.
This
is
a
diagnostic
charger.
The
LED
will
flash
in
a
specific
order
to
indicate
the
battery's
current
status.
(See
figure)
.
4.3.1.2
Fault indication.
When the battery is inserted in the charger and the LEDs flash red,
remove the battery from the charger for a minute and then insert again.
�
If the LEDs flash green, this means that the battery is charging normally.
�
If the LEDs still flash red, remove the battery and unplug the charger again.
Wait a minute, then plug the charger in again and reinsert the battery. If
the LEDs flash green, this means that the battery is charging normally.
�
If the LEDs flash red, the battery is defective and must be replaced.
4.3.2
Battery.
4.3.2.1
Charge verification.
If the battery does not charge correctly :
�
Check the socket using another device. Make sure that
power is reaching the socket.
�
Check that the contacts on the charger have not been
short-circuited by debris or foreign objects.
4.3.3 Storage.
Storing the battery for more than 30 days:
�
Remove the battery from the device.
�
Storage the device in a location where the temperature is
between 7 ̊C et 40 ̊C (45 and 104 ºF).
4.4
Motor.
1 kW DC brushless electric motor.
5
Additional information
5.1
Error codes.
Error codes are generated to identify the cause of the stoppage -
the LEDs flash repeatedly. Here are the most common codes:
DO NOT TOUCH THE CAPSTAN DRUM AFTER USE. IT
MAY BE HOT AND BURN YOUR SKIN.
DURING CLEANING, CHECK THE WINCH, THE HOOKS,
THE LINE AND THE POLYESTER SLING FOR ANY DAMAGE
OR SIGNS OF WEAR.
Regularly remove the capstan
drum and clean around the
shaft. Any accumulated debris
may damage the seal. Brush
the shaft with a little oil to avoid
corrosion.
1
THE
BATTERY
IS
NOT
FULLY
CHARGED.
IT
IS
RECOMMENDED TO CHARGE THE BATTERY FULLY
BEFORE
THE
FIRST
USE
TO
ACHIEVE
MAXIMUM
OPERATING TIME. THIS LITHIUM-ION BATTERY HAS NO
MEMORY
AND
CAN
BE
CHARGED
AT
YOUR
DISCRETION.
1
2
1
2
Never leave the battery on the charger once it is fully charged and
ready to use.
IF THE AMBIENT TEMPERATURE IS UNUSUAL, MOVE THE
CHARGER AND THE BATTERY TO SOMEWHERE WHERE
THE TEMPERATURE IS BETWEEN 7° AND 40 °C (45 AND
104 ºF).
iF THE BATTERY IS INSERTED IN THE CHARGER WHEN IT IS
WARM OR HOT, THE RED LEDs MAY COME ON. IF THIS
HAPPENS, ALLOW THE BATTERY TO COOL AWAY FROM
THE CHARGER. THE BATTERY MAY BE CHARGED
NORMALLY
ONCE
A
NORMAL
CHARGING
TEMPERATURE IS ACHIEVED.
REFER TO THE CHARGER AND BATTERY MANUAL FOR MORE
INFORMATION.
Descriptions
LED code
Definitions
Battery connection
issue
3
No communication between the
battery and the control card.Or loss
of communication during the
current phase.
Surge protection
4
The current process exceeds the
maximum admissible load.
Low-voltage protection
5
The battery charge is
minimum(Recharge the battery).
