background image

Winterizing Your Pump and Long-term Storage

After usage, you can easily empty and store away your pump in a safe place. Some pump owners, however, choose to leave their pump up all year round. In cold areas,

where freezing temperatures occur, there can be a risk of ice damage to your pump. We therefore recommend you drain, disassemble, and properly store the pump,

when the temperature drops below 0ºC (32ºF).

Clean the Pump Water Thoroughly

1. Let the pump cool down for at least 30 minutes before storage. Clean the pump water thoroughly. 

2. Use only damp cloth soaked in mild soap / detergent and water to clean the outer surfaces of the pump. Do not use any kind of chemical or solvent. Always unplug

    the pump and stow the cord during cleaning.

3. Keep out of reach of direct sunlight and chemical substances.

4. Save the original packing box for storage purposes. 

5. Remove the pipes (if applicable) and store in a safe place. Be sure all accessories parts are clean and completely dry before storage. 

6. Bring pump and accessories indoors and store in a safe and dry area, preferably between 0ºC (32ºF) and 40ºC (104ºF).

PUMP STORAGE & WINTERIZING

CUSTOMER SERVICES CONTACT

COUNTRIES / REGIONS

SERVICE CENTER LOCATIONS

United Kingdom

Telephone:

Telephone:

Telephone:

Telephone:

Telephone:

Address:

Address:

Telephone:
Address:

44(0) 1702208172
Geemac sales & Marketing Limited
12 Eldon Way Hockley Essex SS5 4AD

France

33(0) 969360535

Spain

0902848775

Italy

0800788298

12 Eldon Way Hockley Essex

1800-451-190

49(0) 6218455210
Germany Sales & Service Office RMS GmbH
Besselstr.25, 68219 Mannheim 
[email protected]

Australia and Islands

For answers to most frequently asked questions, please visit 

: https://polygroup.zendesk.com/hc/en-us

Germany

17

OWNER’S MANUAL

Содержание SUMMER WAVES SKIMMERPLUS SFX1000-BS



















Отзывы: