POLTI Vaporetto MV 40.20, Инструкция по эксплуатации

Страница: 36 / 120

1.3 FILLING THE WATER (H) AND DETER-
GENT (D) TANK
• Open the cap and fill the water tank (H)
using the funnel and the container with
normal tap water (Pic. 6).
• Close the tank cap.
• Use the funnel to fill the tank (D) with op-
portunely diluted detergent.
• Close the tank cap.
1.4 DETERGENT (not supplied):
Consult the label, the data sheets and the sa-
fety sheets of the substances or detergents
paying attention to the hazard pictograms,
the warnings, the indications and the pruden-
ce advice. Do not use foaming substances or
detergents.
Do not use substances or detergents contai-
ning substances bearing hazard pictograms:
explosive, combustible, flammable, toxic,
harmful, corrosive, irritant, sensitising, carci-
nogenic, mutagenic, toxic for reproduction,
hazardous for the environment.
Never mix together substances and/or deter-
gents.
1.5 PREPARING THE DIRT COLLECTION
BUCKET
• Release the locking lever (F) (Pic. 9) of the
dirt collection bucket and slide the bucket
unit out of the appliance
• Lift the lid (P) of the dirt collection bucket
(U).
• Fill the bucket (U) with 1 litre of tap water.
You can also add into the bucket 1 phial of
Polti Bioecologico, the natural, perfumed
anti-foam deodorant which, in addition to
filling the room with a pleasant perfume,
prevents the formation of foam in the wa-
ter filter, guaranteeing the correct opera-
tion of the appliance. (For more details,
please refer to the Polti Bioecologico chap-
ter).
• Reposition the bucket unit inside.
2. USE FUNCTIONS
The functions of the appliance (steam clea-
ning, vacuuming, detergent and the combi-
ned functions) must be set according to the
type of optional accessories that you decide
to use.
For the optional accessories containing a
flexible hose (1; 9) open the door of the built-
in socket; insert the built-in plug pushing it
(Pic. 7), without pressing the button, until the
hooking mechanism clicks, then check that it
is tight. To disconnect the built-in plug from
the appliance, press the button and pull the
plug to remove it from the appliance.
Completely unwind the power cable and con-
nect it to an appropriate mains socket (Pic.
8). Always use the product with the cord
completely unwound.
2.1 STEAM FUNCTION
It is possible to use this function with: the
Steam & Vacuuming Kit PAEU0374 (chap.
7.1), the Vaporflexi Brush Steam Kit
PAEU0376 (chap. 7.2), the Polti Sani System
Kit PAEU0370 (chap. 7.15), the Steam Mop
accessory PAEU0246 (chap. 7.16).
• Press the main switch (I). The steam ready
light (N) will begin to flash until it becomes
fixed (around 5-10 minutes), at this point
the appliance is ready to generate steam.
• Ensure that the steam lock on the handle is
deactivated (chap. 7.1, chap. 7.2).
• Press the steam request button on the
handle to release steam (chap. 7.1, chap.
7.2).
The basket (G) which has the channel for
housing the extension hoses must be posi-
tioned on the water tank (H). If the baskets
are inverted these will not be in a perfect ho-
rizontal position.
Use the two tubes at the tanks to view the
level of liquid inside the tanks.
WARNING: Pay attention to the intended use
of the two tanks. It is important that the tank
(H) is filled always with water and not with
detergent. The use of detergent in the water
tank could cause serious damage to the pro-
duct. Once the funnel has been used to fill
the detergent tank, rinse it under running wa-
ter before using it to fill the water tank.
WARNING: Any failure caused by the use of
detergents that do not comply with the abo-
ve will be excluded from warranty.
WARNING: Do not release steam if the light
(N) is flashing, wait for it to remain fixed, so
that the system is stabilised and enables the
maximum possible yield.
WARNING: The first time it is used, drops of
water may leak out. This is due to an imper-
fect thermal stabilisation within the sheath.
We therefore recommend directing the first
jet of steam onto a cloth, until a uniform jet
is obtained.
IT
A
L
IA
N
O
E
N
G
L
IS
H
| 36 |