L E C O A S P I R A 9 1 0 - 9 1 0 K I T
Warning:
in particularly cold weather, pre-heat the
windows by applying steam from a distance of
about 50 cm from the surface to be cleaned.
JOKER BRUSH (F) (910 Kit)
With the Joker brush it is possible to remove all
types of solid or liquid dirt, and it will work on any
type of surface.
PARQUET ACCESSORY (G) (910 Kit)
This accessory is for use solely with the Joker
brush. Put the joker brush into place on the parquet
accessory as illustrated in Fig. 13. Apply the brush
to the accessory as indicated by the arrow so that
the two pieces fit onto each other and then hook
them together. To unhook the parquet accessory
from the joker brush pull the two levers on the
sides of the fitting outwards and then lift the brush
off (Fig. 14).
USING THE IRON (910 Kit)
- Connect the iron to the one-piece plug (
B2
) pro-
ceeding as shown in the “Operation” section.
- the iron will start to heat up once the steam gener-
ator reaches the first pressure level, about 5 min
after the appliance is switched on.
S
S
S
S
T
T
T
T
E
E
E
E
A
A
A
A
M
M
M
M
II
II
R
R
R
R
O
O
O
O
N
N
N
N
II
II
N
N
N
N
G
G
G
G
• For steam-ironing, adjust the temperature of the
iron by positioning the temperature control knob
(
Y
) to COTTON-LINEN.
• Wait for some minutes until the “Iron heating” in-
dicator light (
X1
) extinguishes to show that the
soleplate of the iron has reached the required
temperature.
• Press the steam request button (
X
) to enable
the steam to come out. The steam flow will stop
when the push-button is released. When you first
start to use the iron a few drops of water may
come out of the soleplate mixed with the steam
due to imperfect heat stabilisation. It is there-
fore advisable to direct the first jet of steam on-
to a rag.
• In order to obtain a continuous jet of steam
move the sliding switch (
W1
). The steam will
continue to come out even when the steam re-
quest button (
X
) is released. To stop the flow of
steam push the sliding switch backwards (
W1
).
NOTE:
using the iron, it is advisable to adjust the
steam jet at a medium range, or to do some testing
in order to find the jet which is more suitable to the
fabric to be ironed.
D
D
D
D
R
R
R
R
Y
Y
Y
Y
II
II
R
R
R
R
O
O
O
O
N
N
N
N
II
II
N
N
N
N
G
G
G
G
• FOR DRY IRONING ONLY (NOT steam ironing),
press the main switch (
1
) and adjust the temper-
ature of the iron by temperature control knob (
Y
)
to the temperature required for the fabric (as
shown on the knob).
If in doubt about heat level on certain fabrics,
when DRY ironing, it is advisable to use the iron
at a low-range setting first, and gently increase
as and if necessary to avoid damage to fabrics.
II
II
M
M
M
M
P
P
P
P
O
O
O
O
R
R
R
R
T
T
T
T
A
A
A
A
N
N
N
N
T
T
T
T
N
N
N
N
O
O
O
O
T
T
T
T
E
E
E
E
• Never leave the iron unattended while it is on.
• Only iron on surfaces that withstand heat and
that allow the steam to penetrate through them.
An open-mesh ironing board is recommended.
• If you accidentally drop your iron, you should
have it checked by an authorized Polti Service
Centre because some internal malfunctioning
might have occurred, jeopardising the safety of
the product.
•
ATTENTION:
if you iron sitting down, do not
place your legs under the ironing board, the
steam can cause burns.
G
G
G
G
E
E
E
E
N
N
N
N
E
E
E
E
R
R
R
R
A
A
A
A
L
L
L
L
M
M
M
M
A
A
A
A
II
II
N
N
N
N
T
T
T
T
E
E
E
E
N
N
N
N
A
A
A
A
N
N
N
N
C
C
C
C
E
E
E
E
Before carrying out any type of maintenance make
sure that the power cable has been disconnected
from the mains.
After using the brushes it is advisable to allow the
bristles to cool in their natural position so as to
avoid them getting deformed in any way.
Check the conditions of the gaskets located inside
the monobloc plug (
B2
) periodically. If necessary,
replace them with the appropriate spares. Also car-
ry out the same check on the gaskets for connect-
ing the tubes (
D
) and the handle (
A2
).
To clean the outside of the appliance, just use a
damp cloth. Do not use solvents or detergents as
these might damage the plastic surface.
To clean the “ECOACTIVE-FILTER” holder and clean
or change the sponge filter, follow the instructions
in the paragraph headed “EMPTYING AND CLEAN-
ING THE WATER CONTAINER”.
Replacement off the HEPA filter cartridge
Note:
The filter lasts for about 100 hours (approxi-
mately 6 months) when used normally in a domes-
tic environment. If the force of suction drops con-
siderably replace the filter cartridge even before
using it for 100 hours. Unhook the lever for open-
ing the air-output screen (
17
) and rotate it upwards
EE
EE
NN
NN
GG
GG
LL
LL
II
II
SS
SS
HH
HH
Содержание VAPORETTO LECOASPIRA 910 KIT
Страница 1: ...aspira 910 910 KIT ...
