Polarstart PS-2600, Руководство по установке

Страница: 3 / 6

3
TACH ADJUSTMENTS
The PS-2600 has two methods of fine tuning the
tach signal that is generated from the vehicle, the
first
MANUAL TACH SEARCH AND SETTING ,
and the second being AUTOMATIC TACH
SEARCH AND SETTING. Either method can be
used however an automatic search is
recommended.
A tach adjustment procedure
should be done every time a new unit is
installed.
This is because the tach signal from
some vehicles can sometimes be to high or to low,
thus causing failed starts under different
temperatures.
The procedures for tach adjustment are as follows:
1. Hold hood switch down for 6 seconds
2. Release pinswitch (parking lights should come
on)
3. With parking lights on, immediately push and
release pinswitch again.
4. Parking lights will stay on for 20 sec. (if not
repeat from step 1)
5. Press button 1 and 2 of remote transmitter at
the same time. (lights will flash 1 to 7 times)
6. Start the vehicle using the key.
7. If light stay on, then you have selected an
incorrect tach wire.
(relocate tach wire and
start from step 1) If lights go off then proceed
to the next step.
8. Allow vehicle to reach regular engine idle
speed, then press and release brakes. (parking
lights will flash appropriate setting, from 1 to 7
flashes)
9. Press buttons 1 and 2 of remote transmitter, to
save setting. (Parking lights will flash one long
flash)
This feature should only be done by advanced
users. Who feel they would like to fine tune the
setting once an automatic search is done.
MANUAL TACH SEARCH AND SETTING
1. Hold hood switch down for 6 seconds
2. Release pinswitch (parking lights should come
on)
3. With parking lights on, immediately push and
release pinswitch again.
4. Parking lights will stay on for 20 sec. (if not
repeat from step 1)
5. Press button 1 and 2 of remote transmitter at
the same time (lights will flash 1 to 7 times)
6. Now you can increase or decrease the tach
setting, depending on your needs.
7. Button 1 will Decrease the setting, and
button 2 will Increase the setting.
8. After proper setting has been reached, push
Transmitter button 1 and 2 to save setting.
(parking lights should flash once long)
CUSTOM PROGRAMMING OPTIONS
The PS-2600 is equipped with 2 custom
programming menus, that allow the user to
custom fit the PS-2600 according to the
installation requirements.
These options are designed to help make
interfacing with all vehicles possible.
To get into custom programming mode you
must do the following:
1. Hold pinswitch down for 6 sec.
2. Release pinswitch (parking lights will come
on)
3. Immediately push and release pinswitch
once again. (parking lights will stay on for
20 sec.)
4. Press and hold brakes, and simultaneously
press 1 or 2 on remote transmitter. ( Button 1
for mode one, and Button 2 for mode two)
(lights will flash once for mode 1 and twice
for mode 2)
After you have entered into one of the two
programming menus you can release the brake
pedal. The unit will stay in programming mode
until the hood pinswitch is pressed or the valet
switch has been turned off. (
so take your time to
make the proper selection)
The menu will automatically start you at
function one, once you choose from one of the
three Options, you will automatically jump to the
next function.
To select one of the three options press the
appropriate transmitter button. (see below)
1. Button 1 = Option 1
2. Button 2 = Option 2
3. Button 1 + 2 = Option 3
Once an option has been selected the parking
lights will flash 1,2 or 3 times. (
Depending on
option selected)
THE FOLLOWING IS A LIST OF CUSTOM
PROGRAMMING OPTIONS,
(starting with
mode one)