Polaris SLINGSHOT GRAND TOURING 2019 Скачать руководство пользователя

Страница: 107 / 147

CENTER HEADLAMP AIM ADJUSTMENT (USA)

1. Verify that headlamp aim inspection conditions are met.

2. Position the vehicle on a level surface with the nose approximately 25 ft. (7.6

m) from a wall

3. Move the ignition switch to the ON position to turn the lights on. Place the

headlamps on low beam.

4. Observe the headlight beam display on the wall. The beam displays at two

levels, higher at the right side and lower at the left side.

5. Measure from the floor to the lower beam display at the left side as

illustrated. When the beam is properly adjusted, this measurement should be
in the following range:
• 19-20.75” (48-53 cm) for base model
• 20-21.75” (51-55 cm) for SL model

6. To adjust a headlight beam, open the hood and turn the two upper headlamp

adjustment screws

simultaneously and equally.

105

MAINTENANCE

Downloaded from

ManualsNet.com

search engine

Содержание SLINGSHOT GRAND TOURING 2019




















































































































































Результаты поиска

Содержание SLINGSHOT GRAND TOURING 2019

Отзывы:

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренды по названию

Популярные бренды

Polaris SLINGSHOT GRAND TOURING 2019, Руководство пользователя

Результаты поиска

Содержание SLINGSHOT GRAND TOURING 2019

Отзывы:

Похожие инструкции для SLINGSHOT GRAND TOURING 2019

Бренды по названию

Популярные бренды