Polaris PVCR 3200 IQ Home Aqua Black, Руководство по эксплуатации, Страница: 87 / 175

87
way of shaking out, or by means of special brush. If necessary, rinse the HEPA-filter under a thin jet of water of a
room temperature. No detergents shall be used. (Fig. 19)
- Rinse the dust bag under fresh water. (Fig. 20)
- Dry out the filters and dust bag in the natural manner prior to installation.
No heating is allowed.
- Install the filters,
- Close the container and install it on its place.
CLEANING THE WET VACUUMING CONTAINER.
After vacuuming, turn off the vacuum cleaner. Unlatch the rag from the holders.
Rinse the rag with water with detergent, then rinse it in fresh water, then dry it out in the natural manner (without
heating). (Fig. 21)
Empty the water tank, keep the container dry.
CLEANING THE CENTRAL BRUSH
The electric brush is intended for collection of household dust from the floor and carpets by means of a rotating
bristle roller. Its design is quite a susceptible to clogging with long hairs, wool, threads etc. In case of clogging,
you should immediately cease vacuum cleaner operation, and take measures for cleaning the bristle roller.
The
cleaning should be performed each time after vacuuming.
The roller has got a separate electric drive which engages simultaneously with the vacuum cleaner motor.
To clean the roller: (Fig. 22)
1.
Turn off the device through I/O switch (by setting it to "O" position).
2.
Flip the vacuum cleaner so that its rear part faces toward you.
3.
Given a small amount of hairs and threads having wound around the bristle roller, they can be cut away
with a knife without detaching the bristle roller. For this, position a sharp knife between rows of bristles so
that the sharp edge of the knife faces outward from the roller, and then move the knife along the roller to
cut any hairs and threads wound around it. Then, any hair trims can be easily removed out of the brush
body; for your convenience it is allowed to manually rotate the bristle roller around its pivot axis.
4.
Given a severe clogging of the bristle roller, detach the electric brush roller retention frame by a slight
outward exertion on the retainer latch plates, and lift the near end of the frame, then take out the frame.
5.
Slightly lift the right end of the bristle roller by pulling to the right, then unlatch it from the drive, and take
it out of the socket. Having the bristle roller taken out of the body, use a knife or scissors to easily clean the
roller from any hairs and threads wound around it.
6.
Installation of the bristle roller back to its place in the brush body shall be performed in the reverse manner.
7.
Given a severe clogging of components of the brush and electric drive, contact an authorized service center
for disassembling and cleaning.
CLEANING THE LATERAL BRUSHES (Fig. 23)
1. Turn off the vacuum cleaner.
2. Check the brushes for any defects and / or foreign items, as well as debris having wound around.
3. If necessary, detach the brushes.
4. Wipe the brushes with a piece of cloth preliminary soaked in hot water and well wrung. Perform the
cleaning each time after vacuuming.
5. Given any damage to the lateral brushes, timely replace them.
CLEANING THE SENSORS AND CONTACT LEADS
- Make sure to keep the frontal wheel free from debris accrual.
- To remove dust from the fall sensors wipe them with a piece of soft cloth provided exertion no mechanical
impact. (Fig. 24)
- Use a piece of dry soft cloth to wipe the contact leads at the vacuum cleaner bottom, or on the base (Fig. 25)
- Disconnect the electric battery at a long-term idleness of the device.
Any works regarding cleaning external parts of the vacuum cleaner are beyond the warranty service.
TROUBLESHOOTING
The Table contains the most usual problems which may arise during operation the device. Depending on a defect
reason, you can hear 1 to 4 beeps.