Polaris 9940495 Скачать руководство пользователя | Manualshive

Страница: 29 / 48

background image

26

ENVIRONMENT

Sprocket

Check wear on Sprocket by measuring sprocket

teeth as illustrated on Figure 36. Replace

sprocket if dimensions are less than 19 mm.

CAUTION: Excessive wear could lower track drive

efficiency and reduce System performance.

Figure 36

CAUTION: In order that wear on sprockets be

produced evenly across all 4 sprockets, the

vehicle should be driven in 4x4 mode, especially

in abrasive conditions.

ENVIRONMENT

Track Systems are made of varied materials:

steel, aluminum, rubber, plastic, grease & oil used

by the manufacturer. Please recycle, reuse, or

dispose of components at appropriate depot

facilities when Track Systems come to the end of

their life.

PATENTS

The Polaris® Prospector Pro® Track System is

covered by the following patents:
•  CA 2 405 908
•  CA 2 493 181
•  CA 147 901
•  CA 2 822 562
•  CA 2 825 509
•  CA 2 552 119 *
•  CA 2 770 498  *
•  EU 002116731-0001
•  EU 002116731-0002
•  US 6 935 708
•  US 7 229 141
•  US 8 347 991
•  US 8 662 214
•  US 8 967 737
•  US D681,071
•  US D680,561
•  US 7 708 092  *
•  US 8 297 383  *

*

inventor: Jean Després

«
...
27
28
29
30
31
...
»

Содержание 9940495

















































Отзывы:

Нет отзывов

Похожие инструкции для 9940495

Бренд: Garmin Страницы: 205

Бренд: Num'axes Страницы: 64

Бренд: I-gotU Страницы: 17

Hemisphere GPS 750-3001

Бренд: Outback Guidance Страницы: 4

Бренд: Garmin Страницы: 210

Бренд: Garmin Страницы: 102

Бренд: Garmin Страницы: 100

Бренд: Garmin Страницы: 116

Бренд: Garmin Страницы: 96

Бренд: Cobra Страницы: 50

Бренд: TomTom Страницы: 5

Hands-Free Car Kit

Бренд: TomTom Страницы: 14

Бренд: TomTom Страницы: 30

Бренд: TomTom Страницы: 36

Бренд: Tramigo Страницы: 2

Бренд: Tramigo Страницы: 2

Бренд: UniGuard Страницы: 6

Бренд: DiyTracker Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды