background image

24

MAINTENANCE

WEAR

Rubber dampers (Stabilizing arms)

Check  wear  and  damage  on  rubber  dampers

mounted on the stabilizing arms. Replace them if

they  show  cracks  or  are  excessively  worn  or

deformed. See Figure 28.

CAUTION: Improperly adjusted Track systems can

deform and damage the rubber dampers as well as

impair proper operation.

Figure 28

Anti-rotation

Verify wear on Stabilizing arm ball joint to make

sure that it is not seized or too loose. Figure 29.

CAUTION: A damaged ball joint can impede Track

System adjustments and result in damages to the

Track System and to the vehicle if not replaced.

Figure 29

NOTE: For maximum durability of rod end,

disassemble rod end assembly and rotate

ball in its seat to distribute lubricant.

Track

Wear  of  external  profile  impacts  track

performance  directly.  Important  wear  on  profiles

means less traction. Replace track if you notice a

significant loss of performance. Verify internal and

external  rolling  path,  profiles,  and  driving  lugs.

Presence of tears, perforations or delamination in

these  places  can  render  the  Track  system

inoperable. Replace track to prevent failure risks.

See Figure 30.

CAUTION: Too much wear could cause damage to

the Wheels and to the Track guide.

Figure 30

Wheels 

(Ø202mm & Ø134mm)

Verify  wear  on  wheels,  especially  on  interior

guidance  strip.  Replace  wheels  also  if  rolling

band narrows to a width of 24 mm or less -- (29

mm when new). Figure 31.

CAUTION:  A  wheel  that  is  excessively  worn  will

not offer enough support for track guidance.

Figure 31

Содержание 9940495

















































Отзывы: