manualshive.com logo in svg

Polaris 9940495, Руководство пользователя

Поделиться
Скачать
Polaris 9940495 Скачать руководство пользователя страница 24

21

MAINTENANCE

LUBRICATION

The  maintenance  chart  on  page 17  includes

lubrication  maintenance  to  perform  on  the

Track  Systems.  Refer  to  the  following

recommendations for optimal lubrication.

NOTE: Use a grease designed for operation in cold

temperature and in extreme and wet

environments.

REFERENCE “A”

WHEEL  SEAL  LUBRICATION  (Ø202  mm  &

wide Ø134 mm wheels)

Install  new  seal  on  clean,  dry  wheel  shaft  at

position shown below.

NOTE: Installing new wheel seals is recommended

when lubricating these components.

Apply evenly 3 to 3.5 cc of grease all around the

wheel seal’s V–shaped groove.

NOTE: V-shaped groove must be filled with grease all

around.

WHEEL  SEAL  LUBRICATION  (narrow  Ø134

mm wheels)

Install new seal on clean, dry wheel shaft at mid-

point on bearing seat.

NOTE: Installing new wheel seals is recommended

when lubricating these components.

Apply evenly 3 to 3.5 cc of grease all around the

wheel seal’s V–shaped groove.

NOTE: V-shaped groove must be filled with grease.

Содержание 9940495

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды