Polaris 9940495 Скачать руководство пользователя страница 20

Страница: 20 / 48

MAINTENANCE

CAUTION: Regular inspection, adjustment and

lubrication of the Track System is essential to its

good running order and safe operation. Users are

responsible to perform maintenance and regularly

adjust their Track System. The “Maintenance”

section provides the necessary information to

perform adequate maintenance on the Track

System.

CAUTION: Failure to do regular maintenance at

the prescribed intervals and perform the

preventive

adjustments

indicated

the

maintenance schedule can result in premature

wear and important breakage on the Track System

that will not be covered under the warranty. Users

are responsible to follow the maintenance

schedule provided by the manufacturer.

CAUTION: Do not use a brake cleaning solvent to

clean the Track System. This may damage sealing

components and stickers.

The maintenance schedule has been established

in order to provide optimum durability for your

Track System. The type of usage and the

conditions in which the Track System is used,

have a direct bearing on the frequency of

maintenance actions to perform. After inspection

of your Track System, you will be able to

determine if the recommended maintenance

intervals are correct or to adjust them as needed.

For optimum performance and maximum

durability, please refer to the maintenance chart

below.

For more details on the maintenance program,

consult the Maintenance specifications on

page 18 and page 19.



WARNING

Do not insert hands or feet into or near the

System unless the engine is off, and the vehicle is

stopped with the security brake engaged.

MAINTENANCE

INITIAL

INTERVALS

FIRST USE

EVERY 25

- 40

HRS

EVERY 50

- 75

HRS

EVERY 200 HRS

/ ANNUAL

SYSTEM - VISUAL INSPECTION

CLEAN / INSPECT

SYSTEM - ADJUSTMENTS

ADJUST

INSPECT / ADJUST

SYSTEM - VEHICLE ALIGNMENT

ADJUST

INSPECT / ADJUST

SYSTEM - BOLT TORQUE

INSPECT / ADJUST

TRACK- TENSION

ADJUST

INSPECT / ADJUST

TRACK - WEAR

INSPECT

WHEELS - SIDE WEAR

INSPECT / REPLACE

WHEELS - BEARINGS

INSPECT

INSPECT / REPLACE

WHEELS - SEAL LUBRICATION

INSPECT / LUBRICATE

REPLACE / LUBRICATE

FRAME - HUB BEARINGS

INSPECT / REPLACE

FRAME - HUB BEARING SEAL

LUBRICATE

INSPECT / LUBRICATE

FRAME - TRACK GUIDE WEAR

INSPECT / REPLACE

FRAME - STABILIZERS

INSPECT / REPLACE

FRAME - CRACKS

CLEAN / INSPECT

SPROCKETS - WEAR

CLEAN / INSPECT

ANTIROTATION - LUBRICATION

CLEAN / LUBRICATE

ANTIROTATION - BOLT TORQUE

INSPECT / ADJUST

ANTIROTATION - CRACKS, DEFORMATION

INSPECT

VEHICLE - SUSPENSION ARM BOLT TORQUE

INSPECT / ADJUST

VEHICLE - STEERING MECHANISM

INSPECT / ADJUST

: Commercial use / Industrial use / Abrasives conditions

: Normal winter conditions

Important maintenance

Содержание 9940495

















































Результаты поиска

Содержание 9940495

Отзывы:

Polaris 9940495, Руководство пользователя, Страница: 20 / 48

Результаты поиска

Содержание 9940495

Отзывы: