Polaris 502 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 44

background image

13

Step 1
The post bracket and pivot bracket are installed as shown

in fig. 11. **Note - If using supplied brackets for an Amazing

Gate System with posts, please refer to installation

instructions provided with your Amazing Gate.***

Step 2
The gate bracket is installed as shown in fig. 12.

Figure 12

Figure 11

1/2” – 13 Hex

3/8” – 16 x 3” Hex

bolt

Post bracket

3/8” – 16 x 10” Carriage bolt

or all-thread bolt.

Push-to-Open Pivot

Bracket (not included)

3/8” Flat washer

3/8” – 16 Hex nut

Post

1/2” Flat washer

3/8” – 16

Hex nut

3/8” Flat washer

3/8” – 16 x 3”

Hex bolt

Gate

Gate bracket

PUSH-TO-OPEN GATE OPERATOR MOUNTING

«
...
11
12
13
14
15
...
»

Содержание 502













































Отзывы:

Нет отзывов

Похожие инструкции для 502

Бренд: Wayne-Dalton Страницы: 22

Бренд: Eagle Access Control Systems Страницы: 32

MAST SLIM GMASTS05N0G00A

Бренд: Comunello Automation Страницы: 37

Бренд: Seip Страницы: 23

Бренд: SOMFY Страницы: 72

Security+ 4200DI

Бренд: Doit Страницы: 40

Бренд: Delton Страницы: 9

Бренд: CAME Страницы: 2

Бренд: FlexiForce Страницы: 30

Бренд: Power Drive Страницы: 40

Бренд: Power Drive Страницы: 36

AXOVIA 180 B NS

Бренд: SOMFY Страницы: 12

Бренд: SOMFY Страницы: 24

Бренд: SOMFY Страницы: 24

GDO-9 Dynamo Gen 2

Бренд: Automatic Technology Страницы: 36

Бренд: Automatic Technology Страницы: 32

Бренд: Hamilton Beach Страницы: 2

Бренд: Gate1Access Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды