Plymovent OS-4 WRK, Руководство пользователя

Страница: 12 / 14

PUM_WRK_100217_EN 12/14
0
6.
RECEIVER/TRAMSMITTER PROGRAMMING
CAUTION:
Mount the receiver in a location removed from
metal. Metal objects (duct work, wire mesh screens,
boxes) will reduce RF range.
CAUTION:
Graded applications must secure the housing cover
with the included screw.
1. Use the provided anchors and screws to mount the
receiver in a location accessible for future maintenance.
2. Perform a walk test, activating each transmitter assigned
to the receiver and ensuring a good signal.
Dimensions:
165 mm x 89 mm x 25 mm (6.5” x 3.5” x 1”).
Weight:
280 g (.62 lb)
Operating environment:
0°- 60°C (32°- 140°F), 90%
relative humidity, noncondensing.
Power requirement:
11 - 14 VDC; 400 mA
Current consumption:
Approx. 400 mA
Output specifications:
Form C relay 1A @ 28 VDC, 0.5 @
30 VAC resistive load
Input specifications:
A low is less than .5 V; a high is greater
than 2.5 V. Reset input: Contact closure, momentary low.
Receiver type:
Frequency hopping spread spectrum.
Operating frequency:
868-869 MHz
Tamper:
Type B, fixed device.
Number of points/Transmitters:
16.
Number of outputs:
Six Form C relay outputs
Event history log capacity:
50 events (first-in, first-out
replacement).
© Inovonics, 2009 - www.inovonics.com 4
1. Use the provided anchors and screws to mount the receiver in a location
accessible for future maintenance.
2. Perform a walk test, activating each transmitter assigned to the receiver and
ensuring a good signal.
7 Specifications
Dimensions: 165 mm x 89 mm x 25 mm (6.5" x 3.5" x 1").
Weight: 280 g (.62 lb)
Operating environment: 0°- 60°C (32°- 140°F), 90% relative humidity, non-
condensing.
Power requirement: 11 - 14 VDC; 400 mA
Current consumption: Approx. 400 mA
Output specifications: Form C relay 1A @ 28 VDC, 0.5 @ 30 VAC resistive load
Input specifications: A low is less than .5 V; a high is greater than 2.5 V. Reset input:
Contact closure, momentary low.
Receiver type: Frequency hopping spread spectrum.
Operating frequency: 868-869 MHz
Tamper: Type B, fixed device.
Number of points/Transmitters: 16.
Number of outputs: Six Form C relay outputs
Event history log capacity: 50 events (first-in, first-out replacement).
Figure 4 Tamper, Reset, Arm and Clear to Set Circuits
7.1 Means of Conformity
Inovonics Wireless Corporation declares that the product listed above is in conformity
with the essential requirements and provisions of the following Council Directives:
• R&TTE Directive
• Low Voltage Directive
• EMC Directive
and conforms to the following standards:
• EN 300 220 Receiver Class 1, Environmental Category 1
• EN 60950
• EN 301 489
• EN 50130 Environmental Class II
• EN 50131 Security Grade 2
• EN 20131-2-2:2008
• TS 50131-2-2:2004
• PD6662:2004 Incorporating Amendments Numbers 1 and 2
Product tested by Telefication B.V.
8 Warranty/Disclaimer
Caution: Changes or modifications to this unit not expressly approved by Inovonics
Wireless Corporation may void the installer's authority to operate the equipment as
well as the product warranty.
Inovonics Wireless Corporation ("Inovonics") warrants its products ("Product" or
"Products") to conform to its own specifications and to be free of defects in materials
and workmanship under normal use for a period of thirty-six (36) months from the date
of manufacture. Within the warranty period, Inovonics will repair or replace, at its
option, all or any part of the warranted Product. Inovonics will not be responsible for
dismantling and/or reinstallation charges. To exercise the warranty, the User ("User",
"Installer" or "Consumer") must work directly through their authorized distributor who
will be given a Return Material Authorization ("RMA") number by Inovonics. Details of
shipment will be arranged directly through the authorized distributor.
This warranty is void in cases of improper installation, misuse, failure to follow
installation and operating instructions, alteration, accident or tampering, and repair by
anyone other than Inovonics.
This warranty is exclusive and expressly in lieu of all other warranties, obligations or
liabilities, whether written, oral, express, or implied. There is no warranty by Inovonics
that Inovonics product will be merchantable or fit for any particular purpose, nor is
there any other warranty, expressed or implied, except as such is expressly set forth
herein. In no event shall Inovonics be liable for an incidental, consequential, indirect,
special, or exemplary damages, including but not limited to loss of profit, revenue, or
contract, loss of use, cost of down time, or interruption of business, nor any claim
made by distributor's customers or any other person or entity.
This warranty will not be modified or extended. Inovonics does not authorize any
person to act on its behalf to modify or extend this warranty.
This warranty will apply only to Inovonics Products. Inovonics will not be liable for any
direct, incidental, or consequential damage or loss whatsoever, caused by the
malfunction of Product due to products, accessories, or attachments of other
manufacturers, including batteries, used in conjunction with Inovonics Products.
Note: E-mail support@inovonics.com for a copy of the CE Declaration of Conformity.
GN
GN
GN
GN
Tamp
Res
Clear to
Ja
Figure 4 Tamper, Reset, Arm and Clear to Set Circuits
7.1 Means of Conformity
Inovonics Wireless Corporation declares that the product
listed above is in conformity with the essential requirements
and provisions of the following Council Directives:
• R&TTE Directive
• Low Voltage Directive
• EMC Directive and conforms to the following standards:
• EN 300 220 Receiver Class 1, Environmental Category 1
• EN 60950
•
EN 301 489
• EN 50130 Environmental Class II
• EN 50131 Security Grade 2
•
EN 20131-2-2:2008
• TS 50131-2-2:2004
• PD6662:2004 Incorporating Amendments
CAUTION:
Changes or modifications to this unit not expressly
approved by Inovonics Wireless Corporation may
void the installer’s authority to operate the equip-
ment as well as the product warranty.
Inovonics Wireless Corporation (”Inovonics”) warrants its
products (”Product” or”Products”) to conform to its own
specifications and to be free of defects in materials
and workmanship under normal use for a period of thirty-six
(36) months from the date of manufacture. Within the war-
ranty period, Inovonics will repair or replace, at its option, all
or any part of the warranted Product. Inovonics will not be
responsible for dismantling and/or reinstallation charges. To
exercise the warranty, the User (”User”,”Installer” or ”Consu -
mer”) must work directly through their authorized distributor
who will be given a Return Material Authorization (”RMA”)
number by Inovonics. Details of shipment will be arranged di-
rectly through the authorized distributor. This warranty is void
in cases of improper installation, misuse, failure to follow
installation and operating instructions, alteration, accident or
tampering, and repair by anyone other than Inovonics.
This warranty is exclusive and expressly in lieu of all other
warranties, obligations or liabilities, whether written, oral,
express, or implied. There is no warranty by Inovonics that
Inovonics product will be merchantable or fit for any particular
purpose, nor is there any other warranty, expressed or implied,
except as such is expressly set forth herein. In no event shall
Inovonics be liable for an incidental, consequential, indirect,
special, or exemplary damages, including but not limited to loss
of profit, revenue, or contract, loss of use, cost of down time,
or interruption of business, nor any claim made by distributor’s
customers or any other person or entity. This warranty will
not be modified or extended. Inovonics does not authorize any
person to act on its behalf to modify or extend this warranty.
This warranty will apply only to Inovonics Products. Inovonics
will not be liable for any direct, incidental, or consequential da-
mage or loss whatsoever, caused by the malfunction of Product
due to products, accessories, or attachments of other
manufacturers, including batteries, used in conjunction with
Inovonics Products.
’
NOTE:
E-mail support@inovonics.com for a copy of the CE
Declaration of Conformity.
6.6 Mount the Receiver 6.8 Warranty/Disclaimer
6.7 Specifications