Plymovent OS-4 WRK, Руководство пользователя

Страница: 10 / 14

PUM_WRK_100217_EN 10/14
0
NOTE:
Inovonics recommends an LV of four for most instal -
lations. For CENELEC, Grade 2 installations, an LV of
10 or greater is required.
4. To reset signal data, use the Up/Down buttons to leave
and return to the transmitter you are monitoring.
2.10 CTS Type
The EE4216MR provides a signal to the control panel which
can be used to ensure all security devices in the system are ac-
tive before allowing the system to be set. If used by the control
panel, the system cannot be set if the receiver has not heard
from any registered wireless devices within the last 20 minutes.
NOTE:
The CTS signal can be used to block alarming
conditions. This is useful when performing system
tests. For more information on this see “System Test
Mode” on page 10
The CTS TYPE option allows the clear to set signal to be set
to either N/O or N/C. To set the CTS type:
1. From the INSTALL & SERVICE menu, use the Up and
Down buttons to navigate to the CTS TYPE prompt; press
the Enter button.
2. The CTS OP N/O, N/C prompt displays. Use the Up and
Down buttons to choose N/O or N/C; press Enter
to select.
3. The CTS OP SAVED prompt displays; press the Enter
button . © Inovonics, 2009 - www.inovonics.com 3
4. Use the Back button to return to the INSTALL & SERVICE
menu.
2.11 Factory Config
The FACTORY CONFIG option is used to restore the
EE4216MR to its factory defaults.
NOTE:
Caution: Choosing FACTORY CONFIG will erase all
programmed point and output information.
To restore the factory configuration defaults to the EE4216MR:
1. From the INSTALL & SERVICE menu, use the Up and
Down buttons to navigate to the FACTORY CONFIG
prompt; press the Enter button.
2. The RESET CONFIG prompt displays. Use the Up and
Down buttons to choose Y for yes; press Enter to select.
3. The CONFIG RESET prompt displays; press the Enter
button to return to the INSTALL & SERVICE menu.
The receiver can also be brought back to the factory
default configuration through a hardware initiated sequence.
1. Connect a wire between the reset terminal and the
ground terminal
2. While pressing the Back button, cycle the power to the
unit
3. Release the Back button and remove the wire between
the reset terminal and ground
4. RESET CONFIG? displays; press the Enter button
2.12 Select Language
1. At the SELECT LANGUAGE prompt, press Enter.
2. Use the Up/Down buttons to scroll through the language
6.
RECEIVER/TRAMSMITTER PROGRAMMING
options. The CLEAR LANG option resets the language to the
default and exits the INSTALL & SERVICE menu.
3. Press Enter to select language.
4. When LANGUAGE SELECTED displays, press Enter to
return to the INSTALL &
SERVICE menu.
To reset the language selection:
1. Press the
Up and Enter keys while cycling the power.
2. The SELECT LANGUAGE prompt displays. Follow the
steps above to choose a new language.
2.13 Change Password
NOTE:
The CHANGE PASSWORD option only displays
when the level 3 authorized installer is logged in.
Level 2 authorized users do not have the ability to
change passwords.
CAUTION:
Graded applications must have a password of at
least four digits.
Passwords can be up to eight digits long. The default authorized
user password is 3446; the default authorized installer pass -
word is 1234. To change the password:
1. From the INSTALL & SERVICE menu, press
Enter
at the
CHANGE PASSWORD prompt.
2. Use the
Up/Down
buttons to select either USER PASS
WORD or INSTALL PASSWORD;
press
Enter
to select.
3. Use the
Up/Down
buttons to scroll through the digits;
press
Enter
to select and advance to the next digit.
NOTE:
Choosing a null as the first digit of the password will
disable the function, allowing users to perform
receiver functions and/or change parameters
without a password.
4. When finished, press Enter again to complete selection.
5. When PASSWORD CHANGED displays, press
Enter to
return to the INSTALL & SERVICE menu.
CAUTION:
Store the new password in a secure place. If the new
password is lost, you will not be able to access the
receiver without restoring it to factory defaults as
described in section 2.11, “Factory Config” on page
10
System test mode is used to perform a functional test of all of
the transmitters programmed into the system. Upon entry into
test mode, the receiver outputs will be cleared, and transmis-
sions during the test interval will not generate the defined
outputs.
To perform a system test:
1. Enter system test mode.
2. Activate each of the transmitters in the system.
6.3 System Test Mode