Plymovent CONTROLPRO, Руководство по установке

Страница: 6 / 23

0000112606/010720/A ControlPro 5
Optional (for remote access to HMI via network):
- ethernet cable, min. CAT 5E shielded
4.2 Unpacking
Make sure that the product is complete. The
package contains:
4.2.1 ControlPro/Panel
- Panel (control panel)
- double-bit key
- mounting bracket (4), incl. mounting material
- pneumatic hoses, incl. mounting material:
- 2x10 m (for filter pressure)
- 10+1 m (for fan pressure)
- installation manual
- electrical diagram
- UL compliance sticker
11
4.2.2 ControlPro/HMI
- HMI, incl. bracket and locking screw
- ethernet field connector (IP 67)
4.2.3 Connection cables
12
Fig. 4.1
A Panel

HMI cable, incl. heat shrinking tubes
B Panel

SlaveBoard cable
13
, incl. cable gland, termination
plug and heat shrinking tubes
C SlaveBoard

SlaveBoard cable
12
, incl. cable glands
In case of a frequency inverter Plymovent VFD/Panel:
D RS-485 cable
14
(to be ordered separately)
C
B
A
C
B
A
C
B
A
A [cable #1] B [cable #2] C [cable #3]
UNITRONIC® BUS DN
THIN Y
D [cable #4]
Fig. 4.1 Connection cables
4.3 Mounting
ATTENTION
Do not expose any component of ControlPro to
vibrations or heat radiation.
You must install the Panel and HMI at a clearly visible and
accessible position.
11. For use in North America
12. The packages contain mounting material for the cables as well; refer to
paragraph 4.4.4 and 4.4.5
13. MDB only
14. To be ordered separately (due to variable length)
4.3.1 ControlPro/Panel
To install the Panel, do the following.
Fig. 4.2
• Attach the mounting brackets (A) to the Panel with the
supplied mounting material (B).
• Install the Panel to the wall. Make sure that it is level.
ATTENTION
Before you install the Panel, make sure that the wall
is strong enough. Refer to paragraph 1.5.1 for the
weight.
Fig. 4.2
B (4x)
A (4x)
Mounting of the Panel
Fig. 4.3
North America only:
• To comply with UL standard 508A, put the corresponding
sticker on the Panel.
Fig. 4.3
WARNING
Maintenance on Industrial Control
Panels shall only be performed by
trained, qualified, skilled and
authorized electricians, using
appropriate safe electrical work
practices including personal protective
equipment, approved tools, procedures
and accurate drawings of the panels
involved.
CAUTION
Risk of Electric shock
Disconnect Switch may be required to
de-energize before servicing.
AVERTISSEMENT
L'entretien des armoires industrielles
de contrôle doit être effectué
uniquement par des personnes
qualifiées, expertes et autorisés en ce
sens utilisant des méthodes de travail
appropriées et sécurisées, y compris
les équipements de protection
individuelle, les outils, les procédures
approuvées et schémas électrique des
armoires en question.
ATTENTION
Risque de tension électrique
Il pourrait être nécessaire d’installer
un interrupteur principal pour mettre
hors-tension la machine avant
d’entreprendre les travaux d’entretien.
UL compliance sticker
The bottom plate contains the following cable glands and
connectors:
Fig. 4.4
A metal cable gland M20 for the mains cord
B universal cable glands M16 (8)
C bulkhead connectors (4) for the pressure tubes
15
Fig. 4.4
A B C
Bottom plate
Table I on page 21 gives an overview of the necessary and
optional cables that you need to install the system.
• Depending on the selected options and control equipment,
determine the number and type of cables that you need.
15. Fan pr and – | Filter pr and –